| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| The IPv6 neighbour discovery code in subsys/net/ip/ipv6_nbr.c keeps packets that are waiting for address resolution on a per-neighbour pending queue. A queued packet holds two references: the one handed over by the sender and a second one taken by net_ipv6_send_ns() when the packet is put on the queue. The Router Advertisement handler handle_ra_input() popped each packet off the queue and passed it to net_send_data(), relying on a trailing nbr_clear_ns_pending() call to release the queue reference — but that call then found the queue already empty and released nothing, so one reference was leaked for every pending packet flushed on an RA.
Router Advertisements are unauthenticated link-local ICMPv6 messages, so any node on the same link can trigger the flush. An attacker can make the leak deterministic by advertising itself as a router without a source link-layer address option, so the victim's neighbour entry stays INCOMPLETE, then inducing the victim to transmit through that next hop (the packet is queued and a neighbour solicitation is sent), leaving the solicitation unanswered and sending a further RA to drain the queue. Each round leaks one struct net_pkt together with its net_buf chain.
Leaked packets are never returned to the fixed-size pools, so the loss is permanent for the lifetime of the boot. With CONFIG_NET_PKT_TX_COUNT defaulting to 4 (14 with CONFIG_NET_PKT_LARGE_DEFAULTS), a small number of repetitions exhausts the transmit packet slab and the node stops being able to send any traffic. The impact is availability only: the reference count is always too high, never too low, so no use-after-free or memory corruption arises.
The fix moves the flush into a helper, nbr_send_pending(), which releases the queue reference for every packet it takes off the queue before handing the remaining reference to net_send_data(), and releases that one too if the send is refused. |
| Missing release of memory after effective lifetime vulnerability in Apache Tomcat via WebSocket.
This issue affects Apache Tomcat: from 11.0.0-M1 through 11.0.27, from 10.1.0-M1 through 10.1.61, from 9.0.22 through 9.0.123
The following versions were EOL at the time the CVE was created but are known to be affected: from 8.5.0 through 8.5.100, from 7.0.43 through 7.0.109. Other unsupported versions may also be affected.
Users are recommended to upgrade to version 11.0.29, 10.0.62 or 9.0.124, which fix the issue.
Note: Tomcat 11.0.28 was not released |
| aMQTT is an open source MQTT broker and client. From 0.11.0 until 0.12.1, the QoS 2 transaction handler in amqtt/mqtt/protocol/handler.py, _handle_qos2_message_flow(), can retain transaction state and packet identifiers when a client disconnects before the handshake completes, unlike QoS 1 flows that expire after the default five-second timeout. A remote client can repeatedly begin QoS 2 flows and disconnect without maintaining long-lived connections; anonymous clients can do this with the default configuration, while authenticated deployments remain affected when a client may initiate QoS 2 flows. The retained state grows broker memory until resource exhaustion can terminate the process; no confidentiality or integrity impact is identified. This issue is fixed in version 0.12.1. |
| ImageMagick before 7.1.2-18 contains a memory leak vulnerability in the ASHLAR coder when an action fails. Attackers can trigger failed actions to exhaust memory resources and cause denial of service. |
| In Splunk Enterprise versions below 10.4.5, 10.2.9, 10.0.12, and 9.4.17, an unauthenticated user could send repeated HTTP PubSub channel subscription requests that cause a Denial of Service (DoS) by permanently increasing memory usage until Splunk Enterprise exhausts available memory.
The vulnerability affects instances that turn on the [pubsubsvr-http] stanza in server.conf because the HTTP PubSub broker does not release memory associated with a channel after the client disconnects. |
| Missing Release of Memory after Effective Lifetime vulnerability in leandrocp mdex and mdex_native allows an attacker who controls a rendered document to cause a denial of service through unbounded native memory exhaustion.
The native rendering code permanently leaks memory when rendering a document that contains escaped-tag nodes. The conversion of each %MDEx.EscapedTag{} node into its native representation (From<ExEscapedTag> for NodeValue in the Rust NIF) calls Box::leak on the caller-supplied literal string, which surrenders the backing allocation so that it lives for the entire lifetime of the operating system process and is never freed.
Both the byte length of each literal and the number of escaped-tag nodes in a document are attacker-controlled, and there is no size cap, rate limit, or string interning on this path. Every render of a document containing escaped-tag nodes therefore leaks literal_size × node_count bytes that can never be reclaimed, and repeated renders accumulate without bound. Rendering reaches this path through the public MDEx.to_html/1 entry point and any other API that renders a supplied %MDEx.Document{}.
Any application that uses mdex (or mdex_native directly) to render documents derived from user-supplied content is affected. Because the leaked memory is never reclaimed for the life of the BEAM process, an attacker can drive resident memory upward without limit until the node exhausts memory and crashes, taking down every process on it.
The vulnerable native code originally shipped inside mdex (in native/comrak_nif/src/types/document.rs) and was later extracted into the separate mdex_native package (native/mdex_native_nif/src/types/document.rs).
This issue affects mdex: from 0.11.1 before 0.12.3; mdex_native: from 0.1.0 before 0.2.3. |
| Missing release of memory after effective lifetime in Windows DNS allows an unauthorized attacker to deny service over a network. |
| Summary
Cloudflare tokio-quiche was found to contain an uncontrolled resource consumption vulnerability in its HTTP/3 DATAGRAM handling. For every previously unseen flow identifier (quarter stream ID) received in a DATAGRAM frame, tokio-quiche creates and retains new, per-flow state. A remote peer can send DATAGRAMs with many distinct identifiers, causing the per-connection flow map and associated channel state to grow without bound.
Impact
Exploitation can exhaust process memory and cause a denial of service. The vulnerable code is used in both client and server configurations, so either role can be affected by a malicious peer. QUIC DATAGRAM support in tokio-quiche is enabled by default through QuicSettings::enable_dgram; applications can disable it by setting this field to false. The vulnerable HTTP/3 path is reachable only when DATAGRAM support is negotiated with the peer. Core quiche and HTTP/3 deployments without DATAGRAM support are not affected.
Mitigation
Disable DATAGRAMs in tokio-quiche’s QuicSettings::enable_dgram.
Remediation
Upgrade to tokio-quiche version 0.23.0 or later. The fixed code creates flow state only for valid DATAGRAM-capable request streams, which are bounded by QUIC’s stream limits. To tolerate packet reordering, servers retain early DATAGRAMs in a bounded, expiring buffer, while clients discard DATAGRAMs for unknown flows. |
| JSON::XS versions before 4.05 for Perl leak the decoded key of an object rejected for a missing colon in decode_hv.
Unless it is short plain ASCII, a quoted key is decoded into a new scalar. Nothing frees that scalar when the object is rejected for a missing ':' after the key.
A process that keeps running after a failed decode retains one key per rejected document, with its size chosen by the sender. Repeated requests exhaust process memory. |
| JSON::XS versions before 4.05 for Perl leak the decoded part of a rejected long string in decode_str.
A string is decoded through a fixed-size buffer (16 KiB in 4.04), and each time the buffer fills its contents move into a new scalar. Nothing frees that scalar when the string is then rejected for a control character, an invalid escape, malformed UTF-8 or the end of the input.
A process that keeps running after a failed decode retains the decoded part of each rejected string, with its size chosen by the sender. Repeated requests exhaust process memory. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: buffer: hw-consumer: free scan_mask on buffer release
The scan_mask lifetime changed in commit 9a2e1233d38c ("iio: buffer:
hw-consumer: remove redundant scan_mask flexible array").
Before that change, the scan mask storage was embedded in struct
hw_consumer_buffer, so iio_hw_buf_release() could free the whole
allocation with a single kfree(hw_buf).
That commit moved the scan mask to a separate bitmap_zalloc() allocation
stored in buffer.scan_mask, but left iio_hw_buf_release() unchanged.
Free the scan mask in iio_hw_buf_release() before freeing the buffer
wrapper. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: adc: ad_sigma_delta: fix CS held asserted and state leaks
In ad_sigma_delta_single_conversion(), set_mode(AD_SD_MODE_IDLE) and
disable_one() were called from the out: block while keep_cs_asserted
was still true. This caused any SPI transfer issued by those callbacks
to carry cs_change=1, leaving CS permanently asserted after the
conversion. Fix by moving both calls into the out_unlock: block, after
keep_cs_asserted is cleared, matching the pattern already used in
ad_sd_calibrate().
In the error path of ad_sd_buffer_postenable(), if an operation fails
after set_mode(AD_SD_MODE_CONTINUOUS) has already succeeded (e.g.
spi_offload_trigger_enable()), the device is left in continuous
conversion mode with CS physically asserted. Additionally,
bus_locked remaining true after spi_bus_unlock() causes subsequent
SPI operations to call spi_sync_locked() without the bus lock actually
held, allowing concurrent SPI access.
Fix the error path by clearing keep_cs_asserted first, then calling
set_mode(AD_SD_MODE_IDLE) to revert the device mode and deassert CS,
then clearing bus_locked before releasing the bus.
For devices that implement neither set_mode nor disable_one (such as
MAX11205, which has no physical CS pin), no SPI transfer is issued
during cleanup and the cs_change flag has no effect on any physical
line. |
| Uncontrolled resource consumption in Windows Secure Socket Tunneling Protocol (SSTP) allows an unauthorized attacker to deny service over a network. |
| Missing release of memory after effective lifetime in Windows Layer-2 Bridge Network Driver allows an unauthorized attacker to deny service over an adjacent network. |
| Issue summary: A QUIC server that rejects a stream opened by the peer may
retain that stream's state for the lifetime of the connection if the peer
resets the stream before the rejection is signalled, even though the peer's
stream credit is returned.
Impact summary: A remote client that completes a QUIC handshake can repeatedly
open and reset streams, causing server memory to grow without bound until the
process runs out of memory and every connection on it is lost. This is a
Denial of Service.
CWE: CWE-401: Missing Release of Memory after Effective Lifetime
Description: QUIC servers track each stream the peer opens. When the incoming
stream policy rejects a stream, OpenSSL schedules a STOP_SENDING frame, marks
the stream deleted and returns the peer's stream credit. A deleted stream is
collected only once its receive part is fully drained, which for a rejected
stream means the STOP_SENDING has been acknowledged. If the peer sends
RESET_STREAM first, the reset cancels the pending STOP_SENDING, so it is never
sent or acknowledged and the stream is never collected.
The default configuration reaches this path. Once a connection has a default
stream, meaning the application has read from or written to the connection as
the tutorial server does, the effective incoming stream policy rejects streams
the application does not accept. Applications that set the REJECT policy
explicitly are affected too.
Each retained stream costs about 300 bytes, and the peer's stream credit
window paces how quickly they accumulate. A client that keeps the connection
open and keeps opening and resetting streams grows server memory without
bound. The severity is Low because growth is slow, needs a long-lived
connection, and causes no memory corruption or disclosure.
FIPS impact: no
The affected code is outside the FIPS module boundary. |
| In the Linux kernel, the following vulnerability has been resolved:
net: psample: fix info leak in PSAMPLE_ATTR_DATA
psample open codes nla_put() presumably to avoid wiping
the data with 0s just to override it with packet data.
This open coding is missing clearing the pad, however,
each netlink attr is padded to 4B and data_len may
not be divisible by 4B. |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: move policy_bydst RCU sync from per-netns .exit to .pre_exit
The struct pernet_operations docstring in include/net/net_namespace.h
explicitly warns against blocking RCU primitives in .exit handlers:
Exit methods using blocking RCU primitives, such as
synchronize_rcu(), should be implemented via exit_batch.
[...]
Please, avoid synchronize_rcu() at all, where it's possible.
Note that a combination of pre_exit() and exit() can
be used, since a synchronize_rcu() is guaranteed between
the calls.
xfrm_policy_fini() violates this: it calls synchronize_rcu() before
freeing the policy_bydst hash tables (so no RCU reader is mid-
traversal at free time), but runs from xfrm_net_ops.exit -- once per
namespace -- so a cleanup_net() of N namespaces pays N full RCU
grace periods serially.
Use the documented pre_exit/exit split. Move the policy flush (and
the workqueue drains it depends on) into a new .pre_exit handler;
xfrm_policy_fini() then runs in .exit and frees the hash tables
after the synchronize_rcu_expedited() that cleanup_net() guarantees
between the two phases. Providing O(1) RCU grace periods per batch
instead of O(N).
Observed on Linux 6.18 with a workload doing unshare(CLONE_NEWNET)
at ~13/sec sustained: cleanup_net() and the netns_wq rescuer kthread
both stuck in xfrm_policy_fini()'s synchronize_rcu(), >300k struct
net accumulated in the cleanup queue, Percpu in /proc/meminfo climbed
to 130+ GB on 256-CPU hosts, and memcg OOMs followed. setup_net and
__put_net counts were balanced, ruling out a refcount leak. |
| In affected versions of Progress® Telerik® UI for ASP.NET MVC `2012.2.710` through `2026.3.811`, ClassFactory updates a shared class dictionary without exclusive write protection and emits non-collectible dynamic assemblies that remain loaded for the AppDomain's lifetime. The dictionary lookup and insertion are not atomic, and case variations in aggregate descriptors can produce distinct retained types even though member resolution is case-insensitive. An unauthenticated remote attacker can exploit this if the application exposes an aggregation endpoint that is reachable without authentication, by submitting concurrent or repeated crafted requests. These requests may corrupt dictionary state or increase CPU and memory use, potentially degrading availability. The issue is fixed in version `2026.3.1015`. |
| Missing release of memory after effective lifetime vulnerability in openEuler iSulad on Linux.
This vulnerability is associated with program file src/daemon/modules/spec/specs_mount.c.
This issue affects iSulad: through 2.1.6.
The memory leak vulnerability causes the iSulad daemon to be triggered frequently, exhausting the host machine's memory and ultimately leading to an OOM crash of the daemon, resulting in a denial of service (DoS). |
| Missing release of memory after effective lifetime in the MigTD virtio-serial driver for the Intel(R) TDX Migration Trust Domain (MigTD) within Ring 0: Hypervisor may allow a denial of service. System software adversary with a privileged user combined with a low complexity attack may enable denial of service. This result may potentially occur via local access when attack requirements are not present without special internal knowledge and requires no user interaction. The potential vulnerability may impact the confidentiality (none), integrity (none) and availability (low) of the vulnerable system, resulting in subsequent system confidentiality (none), integrity (none) and availability (none) impacts. |