| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: OOB read regression in smb_check_perm_dacl() ACE-walk loops
Commit d07b26f39246 ("ksmbd: require minimum ACE size in
smb_check_perm_dacl()") introduced a transposed bounds check:
if (offsetof(struct smb_ace, sid) + aces_size < CIFS_SID_BASE_SIZE)
Since offsetof(..sid) is 8 and CIFS_SID_BASE_SIZE is 8, this evaluates
to `aces_size < 0`. Because `aces_size` is always non-negative, this
check becomes dead code and never breaks the loop.
Worse, that commit removed the old 4-byte guard, meaning the loop now
reads `ace->size` (offset 2) even when `aces_size` is 0-3 bytes. This
re-opens a 2-byte heap out-of-bounds (OOB) read past the pntsd allocation
during subsequent SMB2_CREATE operations.
Fix this by properly transposing the comparison to require at least
16 bytes (8-byte offset + 8-byte SID base), matching the correct form
used in smb_inherit_dacl(). |
| In the Linux kernel, the following vulnerability has been resolved:
iio: chemical: scd30: fix division by zero in write_raw
Add a zero check for val2 before using it as a divisor when setting the
sampling frequency. A user writing a zero fractional part to the
sampling_frequency sysfs attribute triggers a division by zero in the
kernel. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: typec: ucsi: ccg: reject firmware images without a ':' record header
do_flash() locates the first .cyacd record with
p = strnchr(fw->data, fw->size, ':');
while (p < eof) {
s = strnchr(p + 1, eof - p - 1, ':');
...
}
If the firmware image contains no ':' byte, strnchr() returns NULL.
NULL compares less than the valid kernel pointer eof, so the loop body
runs and strnchr() is called with p + 1 == (void *)1 and a length of
roughly (unsigned long)eof, causing a wonderful crash.
The not_signed_fw fallthrough earlier in do_flash() and the chip-state
branches in ccg_fw_update_needed() allow an unsigned blob to reach this
loop, so a root user who can place a crafted file under /lib/firmware
and write the do_flash sysfs attribute can trigger the oops.
Bail out with -EINVAL when the initial strnchr() returns NULL. |
| A denial of service vulnerability due to a deadlock was found in sctp_auto_asconf_init in net/sctp/socket.c in the Linux kernel’s SCTP subsystem. This flaw allows guests with local user privileges to trigger a deadlock and potentially crash the system. |
| A flaw was found in the blkgs destruction path in block/blk-cgroup.c in the Linux kernel, leading to a cgroup blkio memory leakage problem. When a cgroup is being destroyed, cgroup_rstat_flush() is only called at css_release_work_fn(), which is called when the blkcg reference count reaches 0. This circular dependency will prevent blkcg and some blkgs from being freed after they are made offline. This issue may allow an attacker with a local access to cause system instability, such as an out of memory error. |
| A possible unauthorized memory access flaw was found in the Linux kernel's cpu_entry_area mapping of X86 CPU data to memory, where a user may guess the location of exception stacks or other important data. Based on the previous CVE-2023-0597, the 'Randomize per-cpu entry area' feature was implemented in /arch/x86/mm/cpu_entry_area.c, which works through the init_cea_offsets() function when KASLR is enabled. However, despite this feature, there is still a risk of per-cpu entry area leaks. This issue could allow a local user to gain access to some important data with memory in an expected location and potentially escalate their privileges on the system. |
| In the Linux kernel, the following vulnerability has been resolved:
serial: dz: Convert to use a platform device
Prevent a crash from happening as the first serial port is initialised:
Console: switching to colour frame buffer device 160x64
tgafb: SFB+ detected, rev=0x02
fb0: Digital ZLX-E1 frame buffer device at 0x1e000000
DECstation DZ serial driver version 1.04
CPU 0 Unable to handle kernel paging request at virtual address 000000bc, epc == 8048b3a4, ra == 80470a78
Oops[#1]:
CPU: 0 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.19.0-dirty #35 NONE
$ 0 : 00000000 1000ac00 00000004 804707ac
$ 4 : 00000000 80e20850 80e20858 81000030
$ 8 : 00000000 8072c81c 00000008 fefefeff
$12 : 6c616972 00000006 80c5917f 69726420
$16 : 80e20800 00000000 808f8968 80e20800
$20 : 00000000 807f5a90 808b0094 808d3bc8
$24 : 00000018 80479030
$28 : 80c2e000 80c2fd70 00000069 80470a78
Hi : 00000004
Lo : 00000000
epc : 8048b3a4 __dev_fwnode+0x0/0xc
ra : 80470a78 serial_base_ctrl_add+0xa0/0x168
Status: 1000ac04 IEp
Cause : 30000008 (ExcCode 02)
BadVA : 000000bc
PrId : 00000220 (R3000)
Modules linked in:
Process swapper/0 (pid: 1, threadinfo=(ptrval), task=(ptrval), tls=00000000)
Stack : 00400044 00400040 8046f4cc 00000000 808a6148 808a0000 808f8968 8086983c
808e0000 8046fc84 1000ac01 00000028 80e20700 802ba3f8 80e20700 80d34a94
80c1b900 80e20700 80e20700 80e20700 80e20700 80444650 00000000 00000000
00000000 807f5a90 808b0094 80447080 00400040 808e0000 80d34a94 808a6148
80d34a94 00000004 80e20700 00000000 8076974c 80469810 80c2fe3c 1000ac01
...
Call Trace:
[<8048b3a4>] __dev_fwnode+0x0/0xc
[<80470a78>] serial_base_ctrl_add+0xa0/0x168
[<8046fc84>] serial_core_register_port+0x1c8/0x974
[<808c6af0>] dz_init+0x74/0xc8
[<800470e0>] do_one_initcall+0x44/0x2d4
[<808b111c>] kernel_init_freeable+0x258/0x308
[<8072e434>] kernel_init+0x20/0x114
[<80049cd0>] ret_from_kernel_thread+0x14/0x1c
Code: 27bd0018 03e00008 2402ffea <8c8200bc> 03e00008 00000000 27bdffc0 afbe0038 afb30024
---[ end trace 0000000000000000 ]---
-- where a pointer is dereferenced that has been derived from a null
pointer to the port's parent device.
Since no device is available with legacy probing and it's not anymore a
preferable way to discover devices anyway, switch the driver to using a
platform device and use it as the port's parent device. Update resource
handling accordingly and only request the actual span of addresses used
within the slot, which will have had its resource already requested by
generic platform device code.
Use platform_driver_probe() not just because the DZ device is fixed with
solder on board and not straightforward to remove, but foremost because
the associated TTY's major device number is the same as used by the zs
driver and the first driver to claim it will prevent the other one from
using it. Either one DZ device or some SCC devices will be present in a
given system but never both at a time, and therefore we want the major
device number to be claimed by the first driver to actually successfully
bind to its device and platform_driver_probe() is a way to fulfil that.
An unfortunate consequence of the switch to a platform device is we now
hand the console over from the bootconsole much later in the bootstrap.
The firmware console handler appears good enough though to work so late
and in particular with interrupts enabled.
Conversely only starting the console port so late lets the reset code
fully utilise our delay handlers, so switch from udelay() to fsleep()
for transmitter draining so as to avoid busy-waiting for an excessive
amount of time. |
| In the Linux kernel, the following vulnerability has been resolved:
serial: zs: Convert to use a platform device
Prevent a crash from happening as the first serial port is initialised:
Console: switching to mono frame buffer device 160x64
fb0: PMAG-AA frame buffer device at tc0
DECstation Z85C30 serial driver version 0.10
CPU 0 Unable to handle kernel paging request at virtual address 0000002c, epc == 803ab00c, ra == 803aafe0
Oops[#1]:
CPU: 0 PID: 1 Comm: swapper Not tainted 6.4.0-rc3-00031-g84a9582fd203-dirty #57
$ 0 : 00000000 10012c00 803aaeb0 00000000
$ 4 : 80e12f60 80e12f50 80e12f58 81000030
$ 8 : 00000000 805ff37c 00000000 33433538
$12 : 65732030 00000006 80c2915d 6c616972
$16 : 80e12f00 807b7630 00000000 00000000
$20 : 00000004 00000348 000001a0 807623b8
$24 : 00000018 00000000
$28 : 80c24000 80c25d60 8078b148 803aafe0
Hi : 00000000
Lo : 00000000
epc : 803ab00c serial_base_ctrl_add+0x78/0xf4
ra : 803aafe0 serial_base_ctrl_add+0x4c/0xf4
Status: 10012c03 KERNEL EXL IE
Cause : 00000008 (ExcCode 02)
BadVA : 0000002c
PrId : 00000440 (R4400SC)
Modules linked in:
Process swapper (pid: 1, threadinfo=(ptrval), task=(ptrval), tls=00000000)
Stack : 80760000 00000cc0 00400044 00400040 803aa02c 80d61ab8 00000000 807b7630
80760000 807623b8 807b7628 803aa644 80386998 00000000 80e17780 80220f68
80e17780 80d61ab8 80c17d80 80e17780 80e17780 8063c798 80e17780 80383fa0
00000010 80e17780 00000000 80386998 807a0000 00000000 00400040 8038f848
807623b8 80d61ab8 00000004 80e17780 00000000 803a68e4 80c25e2c 803bb884
...
Call Trace:
[<803ab00c>] serial_base_ctrl_add+0x78/0xf4
[<803aa644>] serial_core_register_port+0x174/0x69c
[<8077e9ac>] zs_init+0xc8/0xfc
[<800404d4>] do_one_initcall+0x40/0x2ac
[<8076cecc>] kernel_init_freeable+0x1e4/0x270
[<80605bec>] kernel_init+0x20/0x108
[<800431e8>] ret_from_kernel_thread+0x14/0x1c
Code: 2442aeb0 ae120024 ae0200d0 <8c67002c> 50e00001 8c670000 3c06806e 3c05806e afb30010
---[ end trace 0000000000000000 ]---
(report at the offending commit) -- where a pointer is dereferenced that
has been derived from a null pointer to the port's parent device.
Since no device is available with legacy probing and it's not anymore a
preferable way to discover devices anyway, switch the driver to using a
platform device and use it as the port's parent device. Update resource
handling accordingly and only request the actual span of addresses used
within the slot, which will have had its resource already requested by
generic platform device code.
Use platform_driver_probe() not just because SCC devices are fixed with
solder on board and not straightforward to remove, but foremost because
the associated TTY's major device number is the same as used by the dz
driver and the first driver to claim it will prevent the other one from
using it. Either one DZ device or some SCC devices will be present in a
given system but never both at a time, and therefore we want the major
device number to be claimed by the first driver to actually successfully
bind to its device and platform_driver_probe() is a way to fulfil that.
An unfortunate consequence of the switch to a platform device is we now
hand the console over from the bootconsole much later in the bootstrap.
The firmware console handler appears good enough though to work so late
and in particular with interrupts enabled.
Since there is one way only remaining to reach zs_reset() now, remove
the port initialisation marker as no longer needed and go through the
channel reset unconditionally. |
| In the Linux kernel, the following vulnerability has been resolved:
USB: serial: safe_serial: fix memory corruption with small endpoint
Make sure that the bulk-out buffer size is at least eight bytes to avoid
user-controlled slab corruption in "safe" mode should a malicious device
report a smaller size. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: L2CAP: fix chan ref leak in l2cap_chan_timeout() on !conn
__set_chan_timer() takes a l2cap_chan reference via l2cap_chan_hold()
before scheduling the delayed work. The normal path in
l2cap_chan_timeout() drops this reference with l2cap_chan_put() at the
end, but the early return when chan->conn is NULL skips the put,
leaking the reference.
Add the missing l2cap_chan_put() before the early return. |
| In the Linux kernel, the following vulnerability has been resolved:
USB: serial: cypress_m8: fix memory corruption with small endpoint
Make sure that the interrupt-out endpoint max packet size is at least
eight bytes to avoid user-controlled slab corruption or NULL-pointer
dereference should a malicious device report a smaller size. |
| IBM Langflow OSS 1.0.0 through 1.10.0 Langflow 1.9.0 could allow server-side request forgery (SSRF) due to insecure default configuration and incomplete enforcement of the SSRF protection mechanism. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: adc: mt6359: fix unchecked return value in mt6358_read_imp
In mt6358_read_imp(), the variable val_v is passed to regmap_read()
but the return value is not checked. If the read fails, val_v remains
uninitialized and its random stack content is subsequently reported
as a measurement result.
Initialize val_v to zero to ensure a predictable value is reported
in case of bus failure and to prevent potential stack data leakage.
This also satisfies static analyzers that might otherwise flag the
variable as used uninitialized. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/migrate_device: fix pgtable leak in migrate_vma_insert_huge_pmd_page
When migrate_vma_insert_huge_pmd_page() jumps to unlock_abort due
to a PMD check failure, the pgtable allocated earlier via
pte_alloc_one() is never freed, causing a memory leak.
Added free_abort label to release the pgtable in error path. |
| In the Linux kernel, the following vulnerability has been resolved:
uio: uio_pci_generic_sva: fix double free of devm_kzalloc() memory
uio_pci_sva allocates struct uio_pci_sva_dev with devm_kzalloc() in
probe(), but then calls kfree(udev) both on the probe() error path
(label out_free) and again in remove().
Because devm_kzalloc() allocations are devres-managed and are freed
automatically when the device is detached (including after a failing
probe() and during driver unbind), the explicit kfree() can lead to a
double free.
If probe() fails after devm_kzalloc(), the error path frees udev and
devres cleanup will free it again when the core unwinds the partially
bound device. On normal driver removal, remove() frees udev and devres
will free it again when the device is detached.
This issue was identified by a static analysis tool I developed and
confirmed by manual review. Fix by removing the manual kfree() calls
and dropping the now-unused label. |
| In the Linux kernel, the following vulnerability has been resolved:
accel/amdxdna: Fix mm_struct reference leak in aie2_populate_range()
aie2_populate_range() jumps back to the again label without calling
mmput(mm), leaking a reference to the mm_struct.
Add the missing mmput() before jumping to again. |
| In the Linux kernel, the following vulnerability has been resolved:
USB: serial: mxuport: fix memory corruption with small endpoint
Make sure that the bulk-out endpoint max packet size is at least eight
bytes to avoid user-controlled slab corruption should a malicious device
report a smaller size. |
| In the Linux kernel, the following vulnerability has been resolved:
USB: serial: digi_acceleport: fix memory corruption with small endpoints
Add the missing bulk-out buffer size sanity checks to avoid
out-of-bounds memory accesses or slab corruption should a malicious
device report smaller buffers than expected. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: composite: fix integer underflow in WebUSB GET_URL handling
The WebUSB GET_URL handler in composite_setup() narrows
landing_page_length to fit the host-supplied wLength using
landing_page_length = w_length
- WEBUSB_URL_DESCRIPTOR_HEADER_LENGTH + landing_page_offset;
If wLength is smaller than WEBUSB_URL_DESCRIPTOR_HEADER_LENGTH the
unsigned subtraction wraps, and the subsequent
memcpy(url_descriptor->URL,
cdev->landing_page + landing_page_offset,
landing_page_length - landing_page_offset);
ends up copying close to UINT_MAX bytes from cdev->landing_page into
cdev->req->buf. KASAN reports a slab-out-of-bounds in composite_setup
on the kmalloc-2k gadget_info allocation, and FORTIFY_SOURCE traps the
memcpy as a 4294967293-byte field-spanning write into
url_descriptor->URL (size 252).
A USB host can reach this from a single SETUP packet against any
gadget that has webusb/use=1 and a landingPage configured.
Handle the small-wLength case before the math: when the host requested
fewer bytes than the URL descriptor header, only the header is
meaningful and no URL bytes need to be copied. Setting
landing_page_length to landing_page_offset makes the existing memcpy a
no-op and leaves the descriptor returned to the host unchanged for all
larger wLength values. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: ISO: Fix data-race on iso_pi fields in hci_get_route calls
iso_connect_bis(), iso_connect_cis(), iso_listen_bis(), and
iso_conn_big_sync() call hci_get_route() using iso_pi(sk)->dst,
iso_pi(sk)->src, and iso_pi(sk)->src_type without holding lock_sock().
These fields may be modified concurrently by connect() or setsockopt()
on the same socket, resulting in data-races reported by KCSAN.
Fix this by snapshotting the required fields under lock_sock() before
calling hci_get_route().
BUG: KCSAN: data-race in memcmp+0x45/0xb0
race at unknown origin, with read to 0xffff8880122135cf of 1 bytes
by task 333 on cpu 1:
memcmp+0x45/0xb0
hci_get_route+0x27e/0x490
iso_connect_cis+0x4c/0xa10
iso_sock_connect+0x60e/0xb30
__sys_connect_file+0xbd/0xe0
__sys_connect+0xe0/0x110
__x64_sys_connect+0x40/0x50
x64_sys_call+0xcad/0x1c60
do_syscall_64+0x133/0x590
entry_SYSCALL_64_after_hwframe+0x77/0x7f |
