Export limit exceeded: 408757 CVEs match your query. Please refine your search to export 10,000 CVEs or fewer.
Search
Search Results (408757 CVEs found)
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2026-46307 | 1 Linux | 1 Linux Kernel | 2026-10-15 | 8.3 High |
| In the Linux kernel, the following vulnerability has been resolved: wifi: ath5k: do not access array OOB Vincent reports: > The ath5k driver seems to do an array-index-out-of-bounds access as > shown by the UBSAN kernel message: > UBSAN: array-index-out-of-bounds in drivers/net/wireless/ath/ath5k/base.c:1741:20 > index 4 is out of range for type 'ieee80211_tx_rate [4]' > ... > Call Trace: > <TASK> > dump_stack_lvl+0x5d/0x80 > ubsan_epilogue+0x5/0x2b > __ubsan_handle_out_of_bounds.cold+0x46/0x4b > ath5k_tasklet_tx+0x4e0/0x560 [ath5k] > tasklet_action_common+0xb5/0x1c0 It is real. 'ts->ts_final_idx' can be 3 on 5212, so: info->status.rates[ts->ts_final_idx + 1].idx = -1; with the array defined as: struct ieee80211_tx_rate rates[IEEE80211_TX_MAX_RATES]; while the size is: #define IEEE80211_TX_MAX_RATES 4 is indeed bogus. Set this 'idx = -1' sentinel only if the array index is less than the array size. As mac80211 will not look at rates beyond the size (IEEE80211_TX_MAX_RATES). Note: The effect of the OOB write is negligible. It just overwrites the next member of info->status, i.e. ack_signal. | ||||
| CVE-2026-46306 | 1 Linux | 1 Linux Kernel | 2026-10-15 | 7.5 High |
| In the Linux kernel, the following vulnerability has been resolved: flow_dissector: do not dissect PPPoE PFC frames RFC 2516 Section 7 states that Protocol Field Compression (PFC) is NOT RECOMMENDED for PPPoE. In practice, pppd does not support negotiating PFC for PPPoE sessions, and the flow dissector driver has assumed an uncompressed frame until the blamed commit. During the review process of that commit [1], support for PFC is suggested. However, having a compressed (1-byte) protocol field means the subsequent PPP payload is shifted by one byte, causing 4-byte misalignment for the network header and an unaligned access exception on some architectures. The exception can be reproduced by sending a PPPoE PFC frame to an ethernet interface of a MIPS board, with RPS enabled, even if no PPPoE session is active on that interface: $ 0 : 00000000 80c40000 00000000 85144817 $ 4 : 00000008 00000100 80a75758 81dc9bb8 $ 8 : 00000010 8087ae2c 0000003d 00000000 $12 : 000000e0 00000039 00000000 00000000 $16 : 85043240 80a75758 81dc9bb8 00006488 $20 : 0000002f 00000007 85144810 80a70000 $24 : 81d1bda0 00000000 $28 : 81dc8000 81dc9aa8 00000000 805ead08 Hi : 00009d51 Lo : 2163358a epc : 805e91f0 __skb_flow_dissect+0x1b0/0x1b50 ra : 805ead08 __skb_get_hash_net+0x74/0x12c Status: 11000403 KERNEL EXL IE Cause : 40800010 (ExcCode 04) BadVA : 85144817 PrId : 0001992f (MIPS 1004Kc) Call Trace: [<805e91f0>] __skb_flow_dissect+0x1b0/0x1b50 [<805ead08>] __skb_get_hash_net+0x74/0x12c [<805ef330>] get_rps_cpu+0x1b8/0x3fc [<805fca70>] netif_receive_skb_list_internal+0x324/0x364 [<805fd120>] napi_complete_done+0x68/0x2a4 [<8058de5c>] mtk_napi_rx+0x228/0xfec [<805fd398>] __napi_poll+0x3c/0x1c4 [<805fd754>] napi_threaded_poll_loop+0x234/0x29c [<805fd848>] napi_threaded_poll+0x8c/0xb0 [<80053544>] kthread+0x104/0x12c [<80002bd8>] ret_from_kernel_thread+0x14/0x1c Code: 02d51821 1060045b 00000000 <8c640000> 3084000f 2c820005 144001a2 00042080 8e220000 To reduce the attack surface and maintain performance, do not process PPPoE PFC frames. [1] https://lore.kernel.org/r/20220630231016.GA392@debian.home | ||||
| CVE-2026-46304 | 1 Linux | 1 Linux Kernel | 2026-10-15 | 7.5 High |
| In the Linux kernel, the following vulnerability has been resolved: nvmet: avoid recursive nvmet-wq flush in nvmet_ctrl_free nvmet_tcp_release_queue_work() runs on nvmet-wq and can drop the final controller reference through nvmet_cq_put(). If that triggers nvmet_ctrl_free(), the teardown path flushes ctrl->async_event_work on the same nvmet-wq. Call chain: nvmet_tcp_schedule_release_queue() kref_put(&queue->kref, nvmet_tcp_release_queue) nvmet_tcp_release_queue() queue_work(nvmet_wq, &queue->release_work) <--- nvmet_wq process_one_work() nvmet_tcp_release_queue_work() nvmet_cq_put(&queue->nvme_cq) nvmet_cq_destroy() nvmet_ctrl_put(cq->ctrl) nvmet_ctrl_free() flush_work(&ctrl->async_event_work) <--- nvmet_wq Previously Scheduled by :- nvmet_add_async_event queue_work(nvmet_wq, &ctrl->async_event_work); This trips lockdep with a possible recursive locking warning. [ 5223.015876] run blktests nvme/003 at 2026-04-07 20:53:55 [ 5223.061801] loop0: detected capacity change from 0 to 2097152 [ 5223.072206] nvmet: adding nsid 1 to subsystem blktests-subsystem-1 [ 5223.088368] nvmet_tcp: enabling port 0 (127.0.0.1:4420) [ 5223.126086] nvmet: Created discovery controller 1 for subsystem nqn.2014-08.org.nvmexpress.discovery for NQN nqn.2014-08.org.nvmexpress:uuid:0f01fb42-9f7f-4856-b0b3-51e60b8de349. [ 5223.128453] nvme nvme1: new ctrl: NQN "nqn.2014-08.org.nvmexpress.discovery", addr 127.0.0.1:4420, hostnqn: nqn.2014-08.org.nvmexpress:uuid:0f01fb42-9f7f-4856-b0b3-51e60b8de349 [ 5233.199447] nvme nvme1: Removing ctrl: NQN "nqn.2014-08.org.nvmexpress.discovery" [ 5233.227718] ============================================ [ 5233.231283] WARNING: possible recursive locking detected [ 5233.234696] 7.0.0-rc3nvme+ #20 Tainted: G O N [ 5233.238434] -------------------------------------------- [ 5233.241852] kworker/u192:6/2413 is trying to acquire lock: [ 5233.245429] ffff888111632548 ((wq_completion)nvmet-wq){+.+.}-{0:0}, at: touch_wq_lockdep_map+0x26/0x90 [ 5233.251438] but task is already holding lock: [ 5233.255254] ffff888111632548 ((wq_completion)nvmet-wq){+.+.}-{0:0}, at: process_one_work+0x5cc/0x6e0 [ 5233.261125] other info that might help us debug this: [ 5233.265333] Possible unsafe locking scenario: [ 5233.269217] CPU0 [ 5233.270795] ---- [ 5233.272436] lock((wq_completion)nvmet-wq); [ 5233.275241] lock((wq_completion)nvmet-wq); [ 5233.278020] *** DEADLOCK *** [ 5233.281793] May be due to missing lock nesting notation [ 5233.286195] 3 locks held by kworker/u192:6/2413: [ 5233.289192] #0: ffff888111632548 ((wq_completion)nvmet-wq){+.+.}-{0:0}, at: process_one_work+0x5cc/0x6e0 [ 5233.294569] #1: ffffc9000e2a7e40 ((work_completion)(&queue->release_work)){+.+.}-{0:0}, at: process_one_work+0x1c5/0x6e0 [ 5233.300128] #2: ffffffff82d7dc40 (rcu_read_lock){....}-{1:3}, at: __flush_work+0x62/0x530 [ 5233.304290] stack backtrace: [ 5233.306520] CPU: 4 UID: 0 PID: 2413 Comm: kworker/u192:6 Tainted: G O N 7.0.0-rc3nvme+ #20 PREEMPT(full) [ 5233.306524] Tainted: [O]=OOT_MODULE, [N]=TEST [ 5233.306525] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.17.0-0-gb52ca86e094d-prebuilt.qemu.org 04/01/2014 [ 5233.306527] Workqueue: nvmet-wq nvmet_tcp_release_queue_work [nvmet_tcp] [ 5233.306532] Call Trace: [ 5233.306534] <TASK> [ 5233.306536] dump_stack_lvl+0x73/0xb0 [ 5233.306552] print_deadlock_bug+0x225/0x2f0 [ 5233.306556] __lock_acquire+0x13f0/0x2290 [ 5233.306563] lock_acquire+0xd0/0x300 [ 5233.306565] ? touch_wq_lockdep_map+0x26/0x90 [ 5233.306571] ? __flush_work+0x20b/0x530 [ 5233.306573] ? touch_wq_lockdep_map+0x26/0x90 [ 5233.306577] touch_wq_lockdep_map+0x3b/0x90 [ 5233.306580] ? touch_wq_lockdep_map+0x26/0x90 [ 52 ---truncated--- | ||||
| CVE-2026-46303 | 1 Linux | 1 Linux Kernel | 2026-10-15 | 8.2 High |
| In the Linux kernel, the following vulnerability has been resolved: isofs: validate Rock Ridge CE continuation extent against volume size rock_continue() reads rs->cont_extent verbatim from the Rock Ridge CE record and passes it to sb_bread() without checking that the block number is within the mounted ISO 9660 volume. commit e595447e177b ("[PATCH] rock.c: handle corrupted directories") added cont_offset and cont_size rejection for the CE continuation but did not validate the extent block number itself. commit f54e18f1b831 ("isofs: Fix infinite looping over CE entries") later capped the CE chain length at RR_MAX_CE_ENTRIES = 32 but again left the block number unchecked. With a crafted ISO mounted via udisks2 (desktop optical auto-mount) or via CAP_SYS_ADMIN mount, rs->cont_extent can therefore point at an out-of-range block or at blocks belonging to an adjacent filesystem on the same block device. sb_bread() on an out-of-range block returns NULL cleanly via the block layer EIO path, so there is no memory-safety violation. For in-range reads of adjacent- filesystem data, the CE buffer is parsed as Rock Ridge records and only the text of SL sub-records reaches userspace through readlink(), which makes the info-leak channel narrow and difficult to exploit; still, rejecting the malformed CE outright matches the rejection shape already present in the same function for cont_offset and cont_size. Add an ISOFS_SB(sb)->s_nzones bounds check to rock_continue() next to the existing offset/size rejection, printing the same corrupted-directory-entry notice. | ||||
| CVE-2026-46294 | 1 Linux | 1 Linux Kernel | 2026-10-15 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: dm: fix a buffer overflow in ioctl processing Tony Asleson (using Claude) found a buffer overflow in dm-ioctl in the function retrieve_status: 1. The code in retrieve_status checks that the output string fits into the output buffer and writes the output string there 2. Then, the code aligns the "outptr" variable to the next 8-byte boundary: outptr = align_ptr(outptr); 3. The alignment doesn't check overflow, so outptr could point past the buffer end 4. The "for" loop is iterated again, it executes: remaining = len - (outptr - outbuf); 5. If "outptr" points past "outbuf + len", the arithmetics wraps around and the variable "remaining" contains unusually high number 6. With "remaining" being high, the code writes more data past the end of the buffer Luckily, this bug has no security implications because: 1. Only root can issue device mapper ioctls 2. The commonly used libraries that communicate with device mapper (libdevmapper and devicemapper-rs) use buffer size that is aligned to 8 bytes - thus, "outptr = align_ptr(outptr)" can't overshoot the input buffer and the bug can't happen accidentally | ||||
| CVE-2026-46275 | 1 Linux | 1 Linux Kernel | 2026-10-15 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci_uart: fix UAFs and race conditions in close and init paths Vulnerabilities leading to Use-After-Free (UAF) and Null Pointer Dereference (NPD) conditions were observed in the lifecycle management of hci_uart. The primary issue arises because the workqueues (init_ready and write_work) are only flushed/cancelled if the HCI_UART_PROTO_READY flag is set during TTY close. If a hangup occurs before setup completes, hci_uart_tty_close() skips the teardown of these workqueues and proceeds to free the `hu` struct. When the scheduled work executes later, it blindly dereferences the freed `hu` struct. Furthermore, several data races and UAFs were identified in the teardown sequence: 1. Calling hci_uart_flush() from hci_uart_close() without effectively disabling write_work causes a race condition where both can concurrently double-free hu->tx_skb. This happens because protocol timers can concurrently invoke hci_uart_tx_wakeup() and requeue write_work. 2. Calling hci_free_dev(hdev) before hu->proto->close(hu) causes a UAF when vendor specific protocol close callbacks dereference hu->hdev. 3. In the initialization error paths, failing to take the proto_lock write lock before clearing PROTO_READY leads to races with active readers. Additionally, hci_uart_tty_receive() accesses hu->hdev outside the read lock, leading to UAFs if the initialization error path frees hdev concurrently. Fix these synchronization and lifecycle issues by: 1. Re-ordering hci_uart_tty_close() to clear HCI_UART_PROTO_READY first, followed immediately by a cancel_work_sync(&hu->write_work). Clearing the flag locks out concurrent protocol timers from successfully invoking hci_uart_tx_wakeup(), effectively rendering the cancellation permanent and preventing the tx_skb double-free. 2. Note: Clearing PROTO_READY early causes hci_uart_close() to skip hu->proto->flush(). This is perfectly safe in the tty_close path because hu->proto->close() executes shortly after, which intrinsically purges all protocol SKB queues and tears down the state. 3. Relocating hu->proto->close(hu) strictly prior to hci_free_dev(hdev) across all close and error paths to prevent vendor-level UAFs. 4. Moving the hdev->stat.byte_rx increment in hci_uart_tty_receive() inside the proto_lock read-side critical section to safely synchronize with device unregistration. 5. Adding cancel_work_sync(&hu->write_work) to hci_uart_close() to safely flush the workqueue before hci_uart_flush() is invoked via the HCI core. 6. Utilizing cancel_work_sync() instead of disable_work_sync() across all paths to prevent permanently breaking user-space retry capabilities. | ||||
| CVE-2026-46243 | 1 Linux | 2 Kernel, Linux Kernel | 2026-10-15 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: smb: client: reject userspace cifs.spnego descriptions cifs.spnego key descriptions contain authority-bearing fields such as pid, uid, creduid, and upcall_target that cifs.upcall treats as kernel-originating inputs. However, userspace can also create keys of this type through request_key(2) or add_key(2), allowing those fields to be supplied without CIFS origin. Only accept cifs.spnego descriptions while CIFS is using its private spnego_cred to request the key. | ||||
| CVE-2026-46234 | 1 Linux | 1 Linux Kernel | 2026-10-15 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: vsock: fix buffer size clamping order In vsock_update_buffer_size(), the buffer size was being clamped to the maximum first, and then to the minimum. If a user sets a minimum buffer size larger than the maximum, the minimum check overrides the maximum check, inverting the constraint. This breaks the intended socket memory boundaries by allowing the vsk->buffer_size to grow beyond the configured vsk->buffer_max_size. Fix this by checking the minimum first, and then the maximum. This ensures the buffer size never exceeds the buffer_max_size. | ||||
| CVE-2026-46227 | 1 Linux | 1 Linux Kernel | 2026-10-15 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: sctp: revalidate list cursor after sctp_sendmsg_to_asoc() in SCTP_SENDALL The SCTP_SENDALL path in sctp_sendmsg() iterates ep->asocs with list_for_each_entry_safe(), which caches the next entry in @tmp before the loop body runs. The body calls sctp_sendmsg_to_asoc(), which may drop the socket lock inside sctp_wait_for_sndbuf(). While the lock is dropped, another thread can SCTP_SOCKOPT_PEELOFF the association cached in @tmp, migrating it to a new endpoint via sctp_sock_migrate() (list_del_init() + list_add_tail() to newep->asocs), and optionally close the new socket which frees the association via kfree_rcu(). The cached @tmp can also be freed by a network ABORT for that association, processed in softirq while the lock is dropped. sctp_wait_for_sndbuf() revalidates @asoc (the current entry) on re-lock via the "sk != asoc->base.sk" and "asoc->base.dead" checks, but nothing revalidates @tmp. After a successful return, the iterator advances to the stale @tmp, yielding either a use-after-free (if the peeled socket was closed) or a list-walk onto the new endpoint's list head (type confusion of &newep->asocs as a struct sctp_association *). Both are reachable from CapEff=0; the type-confusion path gives controlled indirect call via the outqueue.sched->init_sid pointer. Fix by re-deriving @tmp from @asoc after sctp_sendmsg_to_asoc() returns. @asoc is known to still be on ep->asocs at that point: the only callers that list_del an association from ep->asocs are sctp_association_free() (which sets asoc->base.dead) and sctp_assoc_migrate() (which changes asoc->base.sk), and sctp_wait_for_sndbuf() checks both under the lock before any successful return; a tripped check propagates as err < 0 and the loop bails before the re-derive. The SCTP_ABORT path in sctp_sendmsg_check_sflags() returns 0 and the loop hits 'continue' before sctp_sendmsg_to_asoc() is ever called, so the @tmp cached by list_for_each_entry_safe() still covers the lock-held free that ba59fb027307 ("sctp: walk the list of asoc safely") was added for. | ||||
| CVE-2026-46214 | 1 Linux | 1 Linux Kernel | 2026-10-15 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: vsock/virtio: fix accept queue count leak on transport mismatch virtio_transport_recv_listen() calls sk_acceptq_added() before vsock_assign_transport(). If vsock_assign_transport() fails or selects a different transport, the error path returns without calling sk_acceptq_removed(), permanently incrementing sk_ack_backlog. After approximately backlog+1 such failures, sk_acceptq_is_full() returns true, causing the listener to reject all new connections. Fix by moving sk_acceptq_added() to after the transport validation, matching the pattern used by vmci_transport and hyperv_transport. | ||||
| CVE-2026-46209 | 1 Linux | 1 Linux Kernel | 2026-10-15 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: drm/gem: Fix inconsistent plane dimension calculation in drm_gem_fb_init_with_funcs() drm_gem_fb_init_with_funcs() computes sub-sampled plane dimensions using plain integer division: unsigned int width = mode_cmd->width / (i ? info->hsub : 1); unsigned int height = mode_cmd->height / (i ? info->vsub : 1); However, the ioctl-level framebuffer_check() in drm_framebuffer.c uses drm_format_info_plane_width/height() which round up dimensions via DIV_ROUND_UP(). This inconsistency corrupts the subsequent GEM object size check for certain pixel format and dimension combinations. For example, with NV12 (vsub=2) and a 1-pixel-tall framebuffer the GEM size validation path sees height=0 instead of height=1. The expression (height - 1) then wraps to UINT_MAX as an unsigned int, causing min_size to overflow and wrap back to a small value. A tiny GEM object therefore passes the size guard, yet when the GPU accesses the chroma plane it will read or write memory beyond the object's bounds. Fix by replacing the open-coded divisions with drm_format_info_plane_width() and drm_format_info_plane_height(), which use DIV_ROUND_UP() and match the calculation already used in framebuffer_check(). | ||||
| CVE-2026-46196 | 1 Linux | 1 Linux Kernel | 2026-10-15 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: tracepoint: balance regfunc() on func_add() failure in tracepoint_add_func() When a tracepoint goes through the 0 -> 1 transition, tracepoint_add_func() invokes the subsystem's ext->regfunc() before attempting to install the new probe via func_add(). If func_add() then fails (for example, when allocate_probes() cannot allocate a new probe array under memory pressure and returns -ENOMEM), the function returns the error without calling the matching ext->unregfunc(), leaving the side effects of regfunc() behind with no installed probe to justify them. For syscall tracepoints this is particularly unpleasant: syscall_regfunc() bumps sys_tracepoint_refcount and sets SYSCALL_TRACEPOINT on every task. After a leaked failure, the refcount is stuck at a non-zero value with no consumer, and every task continues paying the syscall trace entry/exit overhead until reboot. Other subsystems providing regfunc()/unregfunc() pairs exhibit similarly scoped persistent state. Mirror the existing 1 -> 0 cleanup and call ext->unregfunc() in the func_add() error path, gated on the same condition used there so the unwind is symmetric with the registration. | ||||
| CVE-2026-46195 | 1 Linux | 1 Linux Kernel | 2026-10-15 | 9.8 Critical |
| In the Linux kernel, the following vulnerability has been resolved: smb: client: validate dacloffset before building DACL pointers parse_sec_desc(), build_sec_desc(), and the chown path in id_mode_to_cifs_acl() all add the server-supplied dacloffset to pntsd before proving a DACL header fits inside the returned security descriptor. On 32-bit builds a malicious server can return dacloffset near U32_MAX, wrap the derived DACL pointer below end_of_acl, and then slip past the later pointer-based bounds checks. build_sec_desc() and id_mode_to_cifs_acl() can then dereference DACL fields from the wrapped pointer in the chmod/chown rewrite paths. Validate dacloffset numerically before building any DACL pointer and reuse the same helper at the three DACL entry points. | ||||
| CVE-2026-46193 | 1 Linux | 1 Linux Kernel | 2026-10-15 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: xfrm: ah: account for ESN high bits in async callbacks AH allocates its temporary auth/ICV layout differently when ESN is enabled: the async ahash setup appends a 4-byte seqhi slot before the ICV or auth_data area, but the async completion callbacks still reconstruct the temporary layout as if seqhi were absent. With an async AH implementation selected, that makes AH copy or compare the wrong bytes on both the IPv4 and IPv6 paths. In UML repro on IPv4 AH with ESN and forced async hmac(sha1), ping fails with 100% packet loss, and the callback logs show the pre-fix drift: ah4 output_done: esn=1 err=0 icv_off=20 expected_off=24 ah4 input_done: esn=1 auth_off=20 expected_auth_off=24 icv_off=32 expected_icv_off=36 Reconstruct the callback-side layout the same way the setup path built it by skipping the ESN seqhi slot before locating the saved auth_data or ICV. Per RFC 4302, the ESN high-order 32 bits participate in the AH ICV computation, so the async callbacks must account for the seqhi slot. Post-fix, the same IPv4 AH+ESN+forced-async-hmac(sha1) UML repro shows the corrected offset (ah4 output_done: esn=1 err=0 icv_off=24 expected_off=24) and ping succeeds; net/ipv4/ah4.o and net/ipv6/ah6.o build clean at W=1. IPv6 AH+ESN was not exercised at runtime, and the change has not been tested against a real async hardware AH engine. | ||||
| CVE-2026-46191 | 1 Linux | 1 Linux Kernel | 2026-10-15 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: fbcon: Avoid OOB font access if console rotation fails Clear the font buffer if the reallocation during console rotation fails in fbcon_rotate_font(). The putcs implementations for the rotated buffer will return early in this case. See [1] for an example. Currently, fbcon_rotate_font() keeps the old buffer, which is too small for the rotated font. Printing to the rotated console with a high-enough character code will overflow the font buffer. v2: - fix typos in commit message | ||||
| CVE-2026-46190 | 1 Linux | 1 Linux Kernel | 2026-10-15 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: mtd: spi-nor: debugfs: fix out-of-bounds read in spi_nor_params_show() Sashiko noticed an out-of-bounds read [1]. In spi_nor_params_show(), the snor_f_names array is passed to spi_nor_print_flags() using sizeof(snor_f_names). Since snor_f_names is an array of pointers, sizeof() returns the total number of bytes occupied by the pointers (element_count * sizeof(void *)) rather than the element count itself. On 64-bit systems, this makes the passed length 8x larger than intended. Inside spi_nor_print_flags(), the 'names_len' argument is used to bounds-check the 'names' array access. An out-of-bounds read occurs if a flag bit is set that exceeds the array's actual element count but is within the inflated byte-size count. Correct this by using ARRAY_SIZE() to pass the actual number of string pointers in the array. | ||||
| CVE-2026-46187 | 1 Linux | 1 Linux Kernel | 2026-10-15 | 4.7 Medium |
| In the Linux kernel, the following vulnerability has been resolved: wifi: rsi: fix kthread lifetime race between self-exit and external-stop RSI driver use both self-exit(kthread_complete_and_exit) and external-stop (kthread_stop) when killing a kthread. Generally, kthread_stop() is called first, and in this case, no particular issues occur. However, in rare instances where kthread_complete_and_exit() is called first and then kthread_stop() is called, a UAF occurs because the kthread object, which has already exited and been freed, is accessed again. Therefore, to prevent this with minimal modification, you must remove kthread_stop() and change the code to wait until the self-exit operation is completed. | ||||
| CVE-2026-46185 | 1 Linux | 1 Linux Kernel | 2026-10-15 | 9.1 Critical |
| In the Linux kernel, the following vulnerability has been resolved: smb/client: fix out-of-bounds read in symlink_data() Since smb2_check_message() returns success without length validation for the symlink error response, in symlink_data() it is possible for iov->iov_len to be smaller than sizeof(struct smb2_err_rsp). If the buffer only contains the base SMB2 header (64 bytes), accessing err->ErrorContextCount (at offset 66) or err->ByteCount later in symlink_data() will cause an out-of-bounds read. | ||||
| CVE-2026-46180 | 1 Linux | 1 Linux Kernel | 2026-10-15 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: wifi: brcmfmac: Fix potential use-after-free issue when stopping watchdog task Watchdog task might end between send_sig() and kthread_stop() calls, what results in the use-after-free issue. Fix this by increasing watchdog task reference count before calling send_sig() and dropping it by switching to kthread_stop_put(). | ||||
| CVE-2026-46177 | 1 Linux | 1 Linux Kernel | 2026-10-15 | 7.5 High |
| In the Linux kernel, the following vulnerability has been resolved: ipmi: Add limits to event and receive message requests The driver would just fetch events and receive messages until the BMC said it was done. To avoid issues with BMCs that never say they are done, add a limit of 10 fetches at a time. In addition, an si interface has an attn state it can return from the hardware which is supposed to cause a flag fetch to see if the driver needs to fetch events or message or a few other things. If the attn bit gets stuck, it's a similar problem. So allow messages in between flag fetches so the driver itself doesn't get stuck. This is a more general fix than the previous fix for the specific bad BMC, but should fix the more general issue of a BMC that won't stop saying it has data. This has been there from the beginning of the driver. It's not a bug per-se, but it is accounting for bugs in BMCs. | ||||