| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net: gso: Forbid IPv6 TSO with extensions on devices with only IPV6_CSUM
When performing Generic Segmentation Offload (GSO) on an IPv6 packet that
contains extension headers, the kernel incorrectly requests checksum offload
if the egress device only advertises NETIF_F_IPV6_CSUM feature, which has
a strict contract: it supports checksum offload only for plain TCP or UDP
over IPv6 and explicitly does not support packets with extension headers.
The current GSO logic violates this contract by failing to disable the feature
for packets with extension headers, such as those used in GREoIPv6 tunnels.
This violation results in the device being asked to perform an operation
it cannot support, leading to a `skb_warn_bad_offload` warning and a collapse
of network throughput. While device TSO/USO is correctly bypassed in favor
of software GSO for these packets, the GSO stack must be explicitly told not
to request checksum offload.
Mask NETIF_F_IPV6_CSUM, NETIF_F_TSO6 and NETIF_F_GSO_UDP_L4
in gso_features_check if the IPv6 header contains extension headers to compute
checksum in software.
The exception is a BIG TCP extension, which, as stated in commit
68e068cabd2c6c53 ("net: reenable NETIF_F_IPV6_CSUM offload for BIG TCP packets"):
"The feature is only enabled on devices that support BIG TCP TSO.
The header is only present for PF_PACKET taps like tcpdump,
and not transmitted by physical devices."
kernel log output (truncated):
WARNING: CPU: 1 PID: 5273 at net/core/dev.c:3535 skb_warn_bad_offload+0x81/0x140
...
Call Trace:
<TASK>
skb_checksum_help+0x12a/0x1f0
validate_xmit_skb+0x1a3/0x2d0
validate_xmit_skb_list+0x4f/0x80
sch_direct_xmit+0x1a2/0x380
__dev_xmit_skb+0x242/0x670
__dev_queue_xmit+0x3fc/0x7f0
ip6_finish_output2+0x25e/0x5d0
ip6_finish_output+0x1fc/0x3f0
ip6_tnl_xmit+0x608/0xc00 [ip6_tunnel]
ip6gre_tunnel_xmit+0x1c0/0x390 [ip6_gre]
dev_hard_start_xmit+0x63/0x1c0
__dev_queue_xmit+0x6d0/0x7f0
ip6_finish_output2+0x214/0x5d0
ip6_finish_output+0x1fc/0x3f0
ip6_xmit+0x2ca/0x6f0
ip6_finish_output+0x1fc/0x3f0
ip6_xmit+0x2ca/0x6f0
inet6_csk_xmit+0xeb/0x150
__tcp_transmit_skb+0x555/0xa80
tcp_write_xmit+0x32a/0xe90
tcp_sendmsg_locked+0x437/0x1110
tcp_sendmsg+0x2f/0x50
...
skb linear: 00000000: e4 3d 1a 7d ec 30 e4 3d 1a 7e 5d 90 86 dd 60 0e
skb linear: 00000010: 00 0a 1b 34 3c 40 20 11 00 00 00 00 00 00 00 00
skb linear: 00000020: 00 00 00 00 00 12 20 11 00 00 00 00 00 00 00 00
skb linear: 00000030: 00 00 00 00 00 11 2f 00 04 01 04 01 01 00 00 00
skb linear: 00000040: 86 dd 60 0e 00 0a 1b 00 06 40 20 23 00 00 00 00
skb linear: 00000050: 00 00 00 00 00 00 00 00 00 12 20 23 00 00 00 00
skb linear: 00000060: 00 00 00 00 00 00 00 00 00 11 bf 96 14 51 13 f9
skb linear: 00000070: ae 27 a0 a8 2b e3 80 18 00 40 5b 6f 00 00 01 01
skb linear: 00000080: 08 0a 42 d4 50 d5 4b 70 f8 1a |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: ctnetlink: remove refcounting in expectation dumpers
Same pattern as previous patch: do not keep the expectation object
alive via refcount, only store a cookie value and then use that
as the skip hint for dump resumption.
AFAICS this has the same issue as the one resolved in the conntrack
dumper, when we do
if (!refcount_inc_not_zero(&exp->use))
to increment the refcount, there is a chance that exp == last, which
causes a double-increment of the refcount and subsequent memory leak. |
| In the Linux kernel, the following vulnerability has been resolved:
fs: Prevent file descriptor table allocations exceeding INT_MAX
When sysctl_nr_open is set to a very high value (for example, 1073741816
as set by systemd), processes attempting to use file descriptors near
the limit can trigger massive memory allocation attempts that exceed
INT_MAX, resulting in a WARNING in mm/slub.c:
WARNING: CPU: 0 PID: 44 at mm/slub.c:5027 __kvmalloc_node_noprof+0x21a/0x288
This happens because kvmalloc_array() and kvmalloc() check if the
requested size exceeds INT_MAX and emit a warning when the allocation is
not flagged with __GFP_NOWARN.
Specifically, when nr_open is set to 1073741816 (0x3ffffff8) and a
process calls dup2(oldfd, 1073741880), the kernel attempts to allocate:
- File descriptor array: 1073741880 * 8 bytes = 8,589,935,040 bytes
- Multiple bitmaps: ~400MB
- Total allocation size: > 8GB (exceeding INT_MAX = 2,147,483,647)
Reproducer:
1. Set /proc/sys/fs/nr_open to 1073741816:
# echo 1073741816 > /proc/sys/fs/nr_open
2. Run a program that uses a high file descriptor:
#include <unistd.h>
#include <sys/resource.h>
int main() {
struct rlimit rlim = {1073741824, 1073741824};
setrlimit(RLIMIT_NOFILE, &rlim);
dup2(2, 1073741880); // Triggers the warning
return 0;
}
3. Observe WARNING in dmesg at mm/slub.c:5027
systemd commit a8b627a introduced automatic bumping of fs.nr_open to the
maximum possible value. The rationale was that systems with memory
control groups (memcg) no longer need separate file descriptor limits
since memory is properly accounted. However, this change overlooked
that:
1. The kernel's allocation functions still enforce INT_MAX as a maximum
size regardless of memcg accounting
2. Programs and tests that legitimately test file descriptor limits can
inadvertently trigger massive allocations
3. The resulting allocations (>8GB) are impractical and will always fail
systemd's algorithm starts with INT_MAX and keeps halving the value
until the kernel accepts it. On most systems, this results in nr_open
being set to 1073741816 (0x3ffffff8), which is just under 1GB of file
descriptors.
While processes rarely use file descriptors near this limit in normal
operation, certain selftests (like
tools/testing/selftests/core/unshare_test.c) and programs that test file
descriptor limits can trigger this issue.
Fix this by adding a check in alloc_fdtable() to ensure the requested
allocation size does not exceed INT_MAX. This causes the operation to
fail with -EMFILE instead of triggering a kernel warning and avoids the
impractical >8GB memory allocation request. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Forget ranges when refining tnum after JSET
Syzbot reported a kernel warning due to a range invariant violation on
the following BPF program.
0: call bpf_get_netns_cookie
1: if r0 == 0 goto <exit>
2: if r0 & Oxffffffff goto <exit>
The issue is on the path where we fall through both jumps.
That path is unreachable at runtime: after insn 1, we know r0 != 0, but
with the sign extension on the jset, we would only fallthrough insn 2
if r0 == 0. Unfortunately, is_branch_taken() isn't currently able to
figure this out, so the verifier walks all branches. The verifier then
refines the register bounds using the second condition and we end
up with inconsistent bounds on this unreachable path:
1: if r0 == 0 goto <exit>
r0: u64=[0x1, 0xffffffffffffffff] var_off=(0, 0xffffffffffffffff)
2: if r0 & 0xffffffff goto <exit>
r0 before reg_bounds_sync: u64=[0x1, 0xffffffffffffffff] var_off=(0, 0)
r0 after reg_bounds_sync: u64=[0x1, 0] var_off=(0, 0)
Improving the range refinement for JSET to cover all cases is tricky. We
also don't expect many users to rely on JSET given LLVM doesn't generate
those instructions. So instead of improving the range refinement for
JSETs, Eduard suggested we forget the ranges whenever we're narrowing
tnums after a JSET. This patch implements that approach. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: qat - flush misc workqueue during device shutdown
Repeated loading and unloading of a device specific QAT driver, for
example qat_4xxx, in a tight loop can lead to a crash due to a
use-after-free scenario. This occurs when a power management (PM)
interrupt triggers just before the device-specific driver (e.g.,
qat_4xxx.ko) is unloaded, while the core driver (intel_qat.ko) remains
loaded.
Since the driver uses a shared workqueue (`qat_misc_wq`) across all
devices and owned by intel_qat.ko, a deferred routine from the
device-specific driver may still be pending in the queue. If this
routine executes after the driver is unloaded, it can dereference freed
memory, resulting in a page fault and kernel crash like the following:
BUG: unable to handle page fault for address: ffa000002e50a01c
#PF: supervisor read access in kernel mode
RIP: 0010:pm_bh_handler+0x1d2/0x250 [intel_qat]
Call Trace:
pm_bh_handler+0x1d2/0x250 [intel_qat]
process_one_work+0x171/0x340
worker_thread+0x277/0x3a0
kthread+0xf0/0x120
ret_from_fork+0x2d/0x50
To prevent this, flush the misc workqueue during device shutdown to
ensure that all pending work items are completed before the driver is
unloaded.
Note: This approach may slightly increase shutdown latency if the
workqueue contains jobs from other devices, but it ensures correctness
and stability. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/buffer: fix use-after-free when call bh_read() helper
There's issue as follows:
BUG: KASAN: stack-out-of-bounds in end_buffer_read_sync+0xe3/0x110
Read of size 8 at addr ffffc9000168f7f8 by task swapper/3/0
CPU: 3 UID: 0 PID: 0 Comm: swapper/3 Not tainted 6.16.0-862.14.0.6.x86_64
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996)
Call Trace:
<IRQ>
dump_stack_lvl+0x55/0x70
print_address_description.constprop.0+0x2c/0x390
print_report+0xb4/0x270
kasan_report+0xb8/0xf0
end_buffer_read_sync+0xe3/0x110
end_bio_bh_io_sync+0x56/0x80
blk_update_request+0x30a/0x720
scsi_end_request+0x51/0x2b0
scsi_io_completion+0xe3/0x480
? scsi_device_unbusy+0x11e/0x160
blk_complete_reqs+0x7b/0x90
handle_softirqs+0xef/0x370
irq_exit_rcu+0xa5/0xd0
sysvec_apic_timer_interrupt+0x6e/0x90
</IRQ>
Above issue happens when do ntfs3 filesystem mount, issue may happens
as follows:
mount IRQ
ntfs_fill_super
read_cache_page
do_read_cache_folio
filemap_read_folio
mpage_read_folio
do_mpage_readpage
ntfs_get_block_vbo
bh_read
submit_bh
wait_on_buffer(bh);
blk_complete_reqs
scsi_io_completion
scsi_end_request
blk_update_request
end_bio_bh_io_sync
end_buffer_read_sync
__end_buffer_read_notouch
unlock_buffer
wait_on_buffer(bh);--> return will return to caller
put_bh
--> trigger stack-out-of-bounds
In the mpage_read_folio() function, the stack variable 'map_bh' is
passed to ntfs_get_block_vbo(). Once unlock_buffer() unlocks and
wait_on_buffer() returns to continue processing, the stack variable
is likely to be reclaimed. Consequently, during the end_buffer_read_sync()
process, calling put_bh() may result in stack overrun.
If the bh is not allocated on the stack, it belongs to a folio. Freeing
a buffer head which belongs to a folio is done by drop_buffers() which
will fail to free buffers which are still locked. So it is safe to call
put_bh() before __end_buffer_read_notouch(). |
| In the Linux kernel, the following vulnerability has been resolved:
x86/cpu/hygon: Add missing resctrl_cpu_detect() in bsp_init helper
Since
923f3a2b48bd ("x86/resctrl: Query LLC monitoring properties once during boot")
resctrl_cpu_detect() has been moved from common CPU initialization code to
the vendor-specific BSP init helper, while Hygon didn't put that call in their
code.
This triggers a division by zero fault during early booting stage on our
machines with X86_FEATURE_CQM* supported, where get_rdt_mon_resources() tries
to calculate mon_l3_config with uninitialized boot_cpu_data.x86_cache_occ_scale.
Add the missing resctrl_cpu_detect() in the Hygon BSP init helper.
[ bp: Massage commit message. ] |
| In the Linux kernel, the following vulnerability has been resolved:
net: usb: asix_devices: Fix PHY address mask in MDIO bus initialization
Syzbot reported shift-out-of-bounds exception on MDIO bus initialization.
The PHY address should be masked to 5 bits (0-31). Without this
mask, invalid PHY addresses could be used, potentially causing issues
with MDIO bus operations.
Fix this by masking the PHY address with 0x1f (31 decimal) to ensure
it stays within the valid range. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_reject: don't leak dst refcount for loopback packets
recent patches to add a WARN() when replacing skb dst entry found an
old bug:
WARNING: include/linux/skbuff.h:1165 skb_dst_check_unset include/linux/skbuff.h:1164 [inline]
WARNING: include/linux/skbuff.h:1165 skb_dst_set include/linux/skbuff.h:1210 [inline]
WARNING: include/linux/skbuff.h:1165 nf_reject_fill_skb_dst+0x2a4/0x330 net/ipv4/netfilter/nf_reject_ipv4.c:234
[..]
Call Trace:
nf_send_unreach+0x17b/0x6e0 net/ipv4/netfilter/nf_reject_ipv4.c:325
nft_reject_inet_eval+0x4bc/0x690 net/netfilter/nft_reject_inet.c:27
expr_call_ops_eval net/netfilter/nf_tables_core.c:237 [inline]
..
This is because blamed commit forgot about loopback packets.
Such packets already have a dst_entry attached, even at PRE_ROUTING stage.
Instead of checking hook just check if the skb already has a route
attached to it. |
| In the Linux kernel, the following vulnerability has been resolved:
netlink: avoid infinite retry looping in netlink_unicast()
netlink_attachskb() checks for the socket's read memory allocation
constraints. Firstly, it has:
rmem < READ_ONCE(sk->sk_rcvbuf)
to check if the just increased rmem value fits into the socket's receive
buffer. If not, it proceeds and tries to wait for the memory under:
rmem + skb->truesize > READ_ONCE(sk->sk_rcvbuf)
The checks don't cover the case when skb->truesize + sk->sk_rmem_alloc is
equal to sk->sk_rcvbuf. Thus the function neither successfully accepts
these conditions, nor manages to reschedule the task - and is called in
retry loop for indefinite time which is caught as:
rcu: INFO: rcu_sched self-detected stall on CPU
rcu: 0-....: (25999 ticks this GP) idle=ef2/1/0x4000000000000000 softirq=262269/262269 fqs=6212
(t=26000 jiffies g=230833 q=259957)
NMI backtrace for cpu 0
CPU: 0 PID: 22 Comm: kauditd Not tainted 5.10.240 #68
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.17.0-4.fc42 04/01/2014
Call Trace:
<IRQ>
dump_stack lib/dump_stack.c:120
nmi_cpu_backtrace.cold lib/nmi_backtrace.c:105
nmi_trigger_cpumask_backtrace lib/nmi_backtrace.c:62
rcu_dump_cpu_stacks kernel/rcu/tree_stall.h:335
rcu_sched_clock_irq.cold kernel/rcu/tree.c:2590
update_process_times kernel/time/timer.c:1953
tick_sched_handle kernel/time/tick-sched.c:227
tick_sched_timer kernel/time/tick-sched.c:1399
__hrtimer_run_queues kernel/time/hrtimer.c:1652
hrtimer_interrupt kernel/time/hrtimer.c:1717
__sysvec_apic_timer_interrupt arch/x86/kernel/apic/apic.c:1113
asm_call_irq_on_stack arch/x86/entry/entry_64.S:808
</IRQ>
netlink_attachskb net/netlink/af_netlink.c:1234
netlink_unicast net/netlink/af_netlink.c:1349
kauditd_send_queue kernel/audit.c:776
kauditd_thread kernel/audit.c:897
kthread kernel/kthread.c:328
ret_from_fork arch/x86/entry/entry_64.S:304
Restore the original behavior of the check which commit in Fixes
accidentally missed when restructuring the code.
Found by Linux Verification Center (linuxtesting.org). |
| In the Linux kernel, the following vulnerability has been resolved:
net: usb: asix_devices: add phy_mask for ax88772 mdio bus
Without setting phy_mask for ax88772 mdio bus, current driver may create
at most 32 mdio phy devices with phy address range from 0x00 ~ 0x1f.
DLink DUB-E100 H/W Ver B1 is such a device. However, only one main phy
device will bind to net phy driver. This is creating issue during system
suspend/resume since phy_polling_mode() in phy_state_machine() will
directly deference member of phydev->drv for non-main phy devices. Then
NULL pointer dereference issue will occur. Due to only external phy or
internal phy is necessary, add phy_mask for ax88772 mdio bus to workarnoud
the issue. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: ctnetlink: fix refcount leak on table dump
There is a reference count leak in ctnetlink_dump_table():
if (res < 0) {
nf_conntrack_get(&ct->ct_general); // HERE
cb->args[1] = (unsigned long)ct;
...
While its very unlikely, its possible that ct == last.
If this happens, then the refcount of ct was already incremented.
This 2nd increment is never undone.
This prevents the conntrack object from being released, which in turn
keeps prevents cnet->count from dropping back to 0.
This will then block the netns dismantle (or conntrack rmmod) as
nf_conntrack_cleanup_net_list() will wait forever.
This can be reproduced by running conntrack_resize.sh selftest in a loop.
It takes ~20 minutes for me on a preemptible kernel on average before
I see a runaway kworker spinning in nf_conntrack_cleanup_net_list.
One fix would to change this to:
if (res < 0) {
if (ct != last)
nf_conntrack_get(&ct->ct_general);
But this reference counting isn't needed in the first place.
We can just store a cookie value instead.
A followup patch will do the same for ctnetlink_exp_dump_table,
it looks to me as if this has the same problem and like
ctnetlink_dump_table, we only need a 'skip hint', not the actual
object so we can apply the same cookie strategy there as well. |
| In the Linux kernel, the following vulnerability has been resolved:
rcu/nocb: Fix possible invalid rdp's->nocb_cb_kthread pointer access
In the preparation stage of CPU online, if the corresponding
the rdp's->nocb_cb_kthread does not exist, will be created,
there is a situation where the rdp's rcuop kthreads creation fails,
and then de-offload this CPU's rdp, does not assign this CPU's
rdp->nocb_cb_kthread pointer, but this rdp's->nocb_gp_rdp and
rdp's->rdp_gp->nocb_gp_kthread is still valid.
This will cause the subsequent re-offload operation of this offline
CPU, which will pass the conditional check and the kthread_unpark()
will access invalid rdp's->nocb_cb_kthread pointer.
This commit therefore use rdp's->nocb_gp_kthread instead of
rdp_gp's->nocb_gp_kthread for safety check. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/ptdump: take the memory hotplug lock inside ptdump_walk_pgd()
Memory hot remove unmaps and tears down various kernel page table regions
as required. The ptdump code can race with concurrent modifications of
the kernel page tables. When leaf entries are modified concurrently, the
dump code may log stale or inconsistent information for a VA range, but
this is otherwise not harmful.
But when intermediate levels of kernel page table are freed, the dump code
will continue to use memory that has been freed and potentially
reallocated for another purpose. In such cases, the ptdump code may
dereference bogus addresses, leading to a number of potential problems.
To avoid the above mentioned race condition, platforms such as arm64,
riscv and s390 take memory hotplug lock, while dumping kernel page table
via the sysfs interface /sys/kernel/debug/kernel_page_tables.
Similar race condition exists while checking for pages that might have
been marked W+X via /sys/kernel/debug/kernel_page_tables/check_wx_pages
which in turn calls ptdump_check_wx(). Instead of solving this race
condition again, let's just move the memory hotplug lock inside generic
ptdump_check_wx() which will benefit both the scenarios.
Drop get_online_mems() and put_online_mems() combination from all existing
platform ptdump code paths. |
| In the Linux kernel, the following vulnerability has been resolved:
eventpoll: Fix semi-unbounded recursion
Ensure that epoll instances can never form a graph deeper than
EP_MAX_NESTS+1 links.
Currently, ep_loop_check_proc() ensures that the graph is loop-free and
does some recursion depth checks, but those recursion depth checks don't
limit the depth of the resulting tree for two reasons:
- They don't look upwards in the tree.
- If there are multiple downwards paths of different lengths, only one of
the paths is actually considered for the depth check since commit
28d82dc1c4ed ("epoll: limit paths").
Essentially, the current recursion depth check in ep_loop_check_proc() just
serves to prevent it from recursing too deeply while checking for loops.
A more thorough check is done in reverse_path_check() after the new graph
edge has already been created; this checks, among other things, that no
paths going upwards from any non-epoll file with a length of more than 5
edges exist. However, this check does not apply to non-epoll files.
As a result, it is possible to recurse to a depth of at least roughly 500,
tested on v6.15. (I am unsure if deeper recursion is possible; and this may
have changed with commit 8c44dac8add7 ("eventpoll: Fix priority inversion
problem").)
To fix it:
1. In ep_loop_check_proc(), note the subtree depth of each visited node,
and use subtree depths for the total depth calculation even when a subtree
has already been visited.
2. Add ep_get_upwards_depth_proc() for similarly determining the maximum
depth of an upwards walk.
3. In ep_loop_check(), use these values to limit the total path length
between epoll nodes to EP_MAX_NESTS edges. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Reject narrower access to pointer ctx fields
The following BPF program, simplified from a syzkaller repro, causes a
kernel warning:
r0 = *(u8 *)(r1 + 169);
exit;
With pointer field sk being at offset 168 in __sk_buff. This access is
detected as a narrower read in bpf_skb_is_valid_access because it
doesn't match offsetof(struct __sk_buff, sk). It is therefore allowed
and later proceeds to bpf_convert_ctx_access. Note that for the
"is_narrower_load" case in the convert_ctx_accesses(), the insn->off
is aligned, so the cnt may not be 0 because it matches the
offsetof(struct __sk_buff, sk) in the bpf_convert_ctx_access. However,
the target_size stays 0 and the verifier errors with a kernel warning:
verifier bug: error during ctx access conversion(1)
This patch fixes that to return a proper "invalid bpf_context access
off=X size=Y" error on the load instruction.
The same issue affects multiple other fields in context structures that
allow narrow access. Some other non-affected fields (for sk_msg,
sk_lookup, and sockopt) were also changed to use bpf_ctx_range_ptr for
consistency.
Note this syzkaller crash was reported in the "Closes" link below, which
used to be about a different bug, fixed in
commit fce7bd8e385a ("bpf/verifier: Handle BPF_LOAD_ACQ instructions
in insn_def_regno()"). Because syzbot somehow confused the two bugs,
the new crash and repro didn't get reported to the mailing list. |
| In the Linux kernel, the following vulnerability has been resolved:
padata: Fix pd UAF once and for all
There is a race condition/UAF in padata_reorder that goes back
to the initial commit. A reference count is taken at the start
of the process in padata_do_parallel, and released at the end in
padata_serial_worker.
This reference count is (and only is) required for padata_replace
to function correctly. If padata_replace is never called then
there is no issue.
In the function padata_reorder which serves as the core of padata,
as soon as padata is added to queue->serial.list, and the associated
spin lock released, that padata may be processed and the reference
count on pd would go away.
Fix this by getting the next padata before the squeue->serial lock
is released.
In order to make this possible, simplify padata_reorder by only
calling it once the next padata arrives. |
| In the Linux kernel, the following vulnerability has been resolved:
perf/x86/intel: Fix crash in icl_update_topdown_event()
The perf_fuzzer found a hard-lockup crash on a RaptorLake machine:
Oops: general protection fault, maybe for address 0xffff89aeceab400: 0000
CPU: 23 UID: 0 PID: 0 Comm: swapper/23
Tainted: [W]=WARN
Hardware name: Dell Inc. Precision 9660/0VJ762
RIP: 0010:native_read_pmc+0x7/0x40
Code: cc e8 8d a9 01 00 48 89 03 5b cd cc cc cc cc 0f 1f ...
RSP: 000:fffb03100273de8 EFLAGS: 00010046
....
Call Trace:
<TASK>
icl_update_topdown_event+0x165/0x190
? ktime_get+0x38/0xd0
intel_pmu_read_event+0xf9/0x210
__perf_event_read+0xf9/0x210
CPUs 16-23 are E-core CPUs that don't support the perf metrics feature.
The icl_update_topdown_event() should not be invoked on these CPUs.
It's a regression of commit:
f9bdf1f95339 ("perf/x86/intel: Avoid disable PMU if !cpuc->enabled in sample read")
The bug introduced by that commit is that the is_topdown_event() function
is mistakenly used to replace the is_topdown_count() call to check if the
topdown functions for the perf metrics feature should be invoked.
Fix it. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_core: Fix use-after-free in vhci_flush()
syzbot reported use-after-free in vhci_flush() without repro. [0]
From the splat, a thread close()d a vhci file descriptor while
its device was being used by iotcl() on another thread.
Once the last fd refcnt is released, vhci_release() calls
hci_unregister_dev(), hci_free_dev(), and kfree() for struct
vhci_data, which is set to hci_dev->dev->driver_data.
The problem is that there is no synchronisation after unlinking
hdev from hci_dev_list in hci_unregister_dev(). There might be
another thread still accessing the hdev which was fetched before
the unlink operation.
We can use SRCU for such synchronisation.
Let's run hci_dev_reset() under SRCU and wait for its completion
in hci_unregister_dev().
Another option would be to restore hci_dev->destruct(), which was
removed in commit 587ae086f6e4 ("Bluetooth: Remove unused
hci-destruct cb"). However, this would not be a good solution, as
we should not run hci_unregister_dev() while there are in-flight
ioctl() requests, which could lead to another data-race KCSAN splat.
Note that other drivers seem to have the same problem, for exmaple,
virtbt_remove().
[0]:
BUG: KASAN: slab-use-after-free in skb_queue_empty_lockless include/linux/skbuff.h:1891 [inline]
BUG: KASAN: slab-use-after-free in skb_queue_purge_reason+0x99/0x360 net/core/skbuff.c:3937
Read of size 8 at addr ffff88807cb8d858 by task syz.1.219/6718
CPU: 1 UID: 0 PID: 6718 Comm: syz.1.219 Not tainted 6.16.0-rc1-syzkaller-00196-g08207f42d3ff #0 PREEMPT(full)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 05/07/2025
Call Trace:
<TASK>
dump_stack_lvl+0x189/0x250 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:408 [inline]
print_report+0xd2/0x2b0 mm/kasan/report.c:521
kasan_report+0x118/0x150 mm/kasan/report.c:634
skb_queue_empty_lockless include/linux/skbuff.h:1891 [inline]
skb_queue_purge_reason+0x99/0x360 net/core/skbuff.c:3937
skb_queue_purge include/linux/skbuff.h:3368 [inline]
vhci_flush+0x44/0x50 drivers/bluetooth/hci_vhci.c:69
hci_dev_do_reset net/bluetooth/hci_core.c:552 [inline]
hci_dev_reset+0x420/0x5c0 net/bluetooth/hci_core.c:592
sock_do_ioctl+0xd9/0x300 net/socket.c:1190
sock_ioctl+0x576/0x790 net/socket.c:1311
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:907 [inline]
__se_sys_ioctl+0xf9/0x170 fs/ioctl.c:893
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xfa/0x3b0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7fcf5b98e929
Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 a8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007fcf5c7b9038 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 00007fcf5bbb6160 RCX: 00007fcf5b98e929
RDX: 0000000000000000 RSI: 00000000400448cb RDI: 0000000000000009
RBP: 00007fcf5ba10b39 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 0000000000000000 R14: 00007fcf5bbb6160 R15: 00007ffd6353d528
</TASK>
Allocated by task 6535:
kasan_save_stack mm/kasan/common.c:47 [inline]
kasan_save_track+0x3e/0x80 mm/kasan/common.c:68
poison_kmalloc_redzone mm/kasan/common.c:377 [inline]
__kasan_kmalloc+0x93/0xb0 mm/kasan/common.c:394
kasan_kmalloc include/linux/kasan.h:260 [inline]
__kmalloc_cache_noprof+0x230/0x3d0 mm/slub.c:4359
kmalloc_noprof include/linux/slab.h:905 [inline]
kzalloc_noprof include/linux/slab.h:1039 [inline]
vhci_open+0x57/0x360 drivers/bluetooth/hci_vhci.c:635
misc_open+0x2bc/0x330 drivers/char/misc.c:161
chrdev_open+0x4c9/0x5e0 fs/char_dev.c:414
do_dentry_open+0xdf0/0x1970 fs/open.c:964
vfs_open+0x3b/0x340 fs/open.c:1094
do_open fs/namei.c:3887 [inline]
path_openat+0x2ee5/0x3830 fs/name
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
NFSD: fix race between nfsd registration and exports_proc
As of now nfsd calls create_proc_exports_entry() at start of init_nfsd
and cleanup by remove_proc_entry() at last of exit_nfsd.
Which causes kernel OOPs if there is race between below 2 operations:
(i) exportfs -r
(ii) mount -t nfsd none /proc/fs/nfsd
for 5.4 kernel ARM64:
CPU 1:
el1_irq+0xbc/0x180
arch_counter_get_cntvct+0x14/0x18
running_clock+0xc/0x18
preempt_count_add+0x88/0x110
prep_new_page+0xb0/0x220
get_page_from_freelist+0x2d8/0x1778
__alloc_pages_nodemask+0x15c/0xef0
__vmalloc_node_range+0x28c/0x478
__vmalloc_node_flags_caller+0x8c/0xb0
kvmalloc_node+0x88/0xe0
nfsd_init_net+0x6c/0x108 [nfsd]
ops_init+0x44/0x170
register_pernet_operations+0x114/0x270
register_pernet_subsys+0x34/0x50
init_nfsd+0xa8/0x718 [nfsd]
do_one_initcall+0x54/0x2e0
CPU 2 :
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000010
PC is at : exports_net_open+0x50/0x68 [nfsd]
Call trace:
exports_net_open+0x50/0x68 [nfsd]
exports_proc_open+0x2c/0x38 [nfsd]
proc_reg_open+0xb8/0x198
do_dentry_open+0x1c4/0x418
vfs_open+0x38/0x48
path_openat+0x28c/0xf18
do_filp_open+0x70/0xe8
do_sys_open+0x154/0x248
Sometimes it crashes at exports_net_open() and sometimes cache_seq_next_rcu().
and same is happening on latest 6.14 kernel as well:
[ 0.000000] Linux version 6.14.0-rc5-next-20250304-dirty
...
[ 285.455918] Unable to handle kernel paging request at virtual address 00001f4800001f48
...
[ 285.464902] pc : cache_seq_next_rcu+0x78/0xa4
...
[ 285.469695] Call trace:
[ 285.470083] cache_seq_next_rcu+0x78/0xa4 (P)
[ 285.470488] seq_read+0xe0/0x11c
[ 285.470675] proc_reg_read+0x9c/0xf0
[ 285.470874] vfs_read+0xc4/0x2fc
[ 285.471057] ksys_read+0x6c/0xf4
[ 285.471231] __arm64_sys_read+0x1c/0x28
[ 285.471428] invoke_syscall+0x44/0x100
[ 285.471633] el0_svc_common.constprop.0+0x40/0xe0
[ 285.471870] do_el0_svc_compat+0x1c/0x34
[ 285.472073] el0_svc_compat+0x2c/0x80
[ 285.472265] el0t_32_sync_handler+0x90/0x140
[ 285.472473] el0t_32_sync+0x19c/0x1a0
[ 285.472887] Code: f9400885 93407c23 937d7c27 11000421 (f86378a3)
[ 285.473422] ---[ end trace 0000000000000000 ]---
It reproduced simply with below script:
while [ 1 ]
do
/exportfs -r
done &
while [ 1 ]
do
insmod /nfsd.ko
mount -t nfsd none /proc/fs/nfsd
umount /proc/fs/nfsd
rmmod nfsd
done &
So exporting interfaces to user space shall be done at last and
cleanup at first place.
With change there is no Kernel OOPs. |
