| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
drm/pagemap: Prevent double migration of device pages
A device-private folio migrated to system memory by a CPU fault can
remain reachable through the raw-PFN eviction path until migration
finalization drops the source reference.
If eviction selects the same device-private folio during this window,
it can attempt to migrate the folio again. The second migration can leave
an uncharged folio on an LRU list, causing folio_lruvec_lock_irqsave() to
retry indefinitely and resulting in a soft lockup and RCU stall.
Mark successfully migrated device-private folios using a low bit of
their zone_device_data before migration finalization. Make both CPU-fault
and raw-PFN migration paths skip device-private folios carrying this
flag.
Mask the flag when retrieving the drm_pagemap_zdd pointer and preserve
it when a device-private folio is split. Keeping the state on the physical
folio also avoids depending on a virtual address that may change before a
fault occurs.
v2:
- Replace the retired-PFN XArray with an embedded bitmap. (Matthew Brost)
- Mark every base page covered by a migrated folio so retirement remains
valid if the folio is later split.
v3:
- Store the migrated state in a low bit of zone_device_data instead of
adding virtual-range and bitmap tracking to the ZDD. (Matthew Brost)
- Mask the flag when retrieving the ZDD and preserve it when splitting
a folio.
- Drop the pre-existing fixes already covered by Matthew Brost's series:
https://patchwork.freedesktop.org/series/171651/
v4:
- Advance by the folio size only for migration entries marked with
MIGRATE_PFN_COMPOUND. (Sashiko)
v5:
- Simplify ZDD flag updates and folio iteration. (Matthew Brost)
- Skip retired device-private folios in the CPU-fault path. (Matthew Brost)
- Preserve flag bits while taking a new ZDD reference for split folios.
v6:
- Restore MIGRATE_PFN_COMPOUND-aware stepping so non-compound migration
entries are processed one at a time. (Sashiko)
- Drop the pre-existing fixes already covered by Matthew Brost's series:
https://patchwork.freedesktop.org/series/171651/
The lockup was observed as:
[10109.860465] watchdog: BUG: soft lockup - CPU#9 stuck for 26s! [kworker/u65:5:6557]
[10109.860524] Tainted: [S]=CPU_OUT_OF_SPEC, [O]=OOT_MODULE
[10109.860524] Hardware name: ASUS System Product Name/PRIME Z790-P WIFI, BIOS 0812 02/24/2023
[10109.860525] Workqueue: xe_page_fault_work_queue xe_pagefault_queue_work [xe]
[10109.860644] RIP: 0010:_raw_spin_unlock_irqrestore+0x57/0x80
[10109.860655] Call Trace:
[10109.860655] <TASK>
[10109.860657] folio_lruvec_lock_irqsave+0x216/0x220
[10109.860661] ? __pfx_lru_add+0x10/0x10
[10109.860665] folio_batch_move_lru+0xc8/0x450
[10109.860670] ? lock_acquire+0xc4/0x2d0
[10109.860674] ? __folio_batch_add_and_move+0x60/0x2e0
[10109.860677] ? folio_migrate_mapping+0xa6/0x110
[10109.860679] ? folio_migrate_flags+0x13b/0x1b0
[10109.860681] ? __pfx_lru_add+0x10/0x10
[10109.860683] __folio_batch_add_and_move+0xe7/0x2e0
[10109.860685] ? dma_iova_try_alloc+0xb0/0x140
[10109.860689] folio_add_lru+0x64/0x80
[10109.860691] __migrate_device_finalize+0x12c/0x270
[10109.860695] migrate_device_finalize+0x10/0x20
[10109.860698] drm_pagemap_evict_to_ram+0x185/0x370 [drm_gpusvm_helper]
[10109.860704] ? drm_pagemap_evict_to_ram+0x96/0x370 [drm_gpusvm_helper]
[10109.860709] xe_svm_bo_evict+0x15/0x20 [xe]
[10109.860819] ? xe_svm_bo_evict+0x15/0x20 [xe]
[10109.860921] xe_bo_move+0x107e/0x1570 [xe]
[10109.860992] ? xe_ttm_tt_create+0x168/0x340 [xe]
[10109.861059] ? __up_read+0x98/0x2b0
[10109.861061] ? lock_is_held_type+0xa3/0x130
[10109.861067] ttm_bo_handle_move_mem+0xe8/0x1e0 [ttm]
[10109.861075] ttm_bo_evict+0x141/0x1c0 [ttm]
[10109.861081] ttm_bo_evict_cb+0x9f/0x100 [ttm]
[10109.861086] ttm_lru_walk_for_evict+0x84/0x190 [ttm]
[10109.861091] ? xe_ttm_vram_mgr_new+0x258/0x3a0 [xe]
[10109.861198] ttm_bo_alloc_resource+0x219/0
---truncated--- |
| Zammad is a web based open source helpdesk/customer support system. Prior to 7.1.2, a user with Knowledge Base editing rights for a category can embed a video widget in a published answer with a specially crafted value. When the answer is rendered, that value is inserted into the page's HTML without being escaped for its attribute context, allowing it to break out and inject additional HTML into the page. When another user who has permission to switch between user sessions views the affected answer, the injected HTML causes their browser to silently send a request to Zammad's session-switching endpoint using their own active credentials. This results in switching their session to an account chosen by the person who wrote the Knowledge Base answer. No action is required from the viewer beyond opening the published answer. This issue is fixed in version 7.1.2. |
| In the Linux kernel, the following vulnerability has been resolved:
xfs: don't spin forever on zero-length dirents when salvaging them
LOLLM noticed that xrep_dir_recover_data can spin forever if it
encounters an unused dirent that claims to have length zero. Fix that,
and prevent the same thing from happening with a zero-length entry. |
| urllib3 is an HTTP client library for Python. From 2.6.2 until 2.8.0, HTTPResponse.stream and HTTPResponse.read_chunked can enter an infinite loop because the Deflate decoder retains trailing bytes as unconsumed input after reaching end-of-stream and repeatedly decodes them without progress. The issue occurs when an untrusted server sends a chunked Deflate response whose decoded body exceeds a positive finite chunk size and whose encoded body has trailing bytes, specifically a response with Transfer-Encoding: chunked and Content-Encoding: deflate, content decoding enabled, and the positive finite amt=N streaming chunk size. The attack mechanism is that a malicious server returns a compressed chunked response with trailing bytes after the Deflate stream. The impact is excessive CPU usage and a request that does not complete, and network read timeouts do not interrupt the loop because no further socket read occurs. This issue is fixed in version 2.8.0. |
| Pod::Text versions before 6.1.1 for Perl allow CPU and memory exhaustion formatting a POD document whose =over nesting drives the margin to the output width.
Each =over adds its indent to the margin, which wrap() subtracts from the output width to get the space available for text. When that space reaches zero, the line-splitting substitution matches the empty string, and the loop consumes no input while appending the margin padding on every pass.
Formatting an attacker-supplied POD document never returns, and the output grows until memory is exhausted. |
| Net::IDN::Punycode versions before 2.590 for Perl hang, crash or return a wrong label via unvalidated malformed UTF-8 in encode_punycode.
Neither backend checks that its input is well-formed UTF-8, so a string with the UTF-8 flag set over malformed bytes, as the :utf8 PerlIO layer produces from any malformed input, reaches the encoder unchecked. On perl 5.32 and later the XS backend reports a malformed sequence with a length of `(STRLEN)-1`, so the scan steps back one byte instead of forward and never ends. On earlier perls the XS returns a valid label for a different name. The pure-Perl backend runs a regex over the flagged string. Depending on the bytes, it aborts with SIGBUS on perl 5.28 and later, dies with a panic, or returns a wrong label.
The documented conversion functions match the label against Unicode properties first and that match dies on such a string, so only a direct call to encode_punycode reaches the defect. The decoder is not affected.
A direct caller encoding attacker-supplied bytes hangs, crashes or gets a label for a name the input never held. |
| js-yaml is a JavaScript YAML parser and dumper. From 3.0.0 until 3.15.2, 4.3.2, and 5.4.1, maxTotalMergeKeys in lib/js-yaml/loader.js and lib/loader.js does not count empty mapping sources while processing the merge key <<. An attacker can alias a large sequence of empty mappings into many merge targets, causing O(N * K) processing while totalMergeKeys remains unchanged and the configured resource limit is never reached. A relatively small YAML document can therefore cause prolonged CPU consumption in applications that parse untrusted YAML, and merge processing is enabled by default on these release lines. In v3 & v4, merge is enabled by default so the severity score is higher. This issue is fixed in versions 3.15.2, 4.3.2, and 5.4.1. |
| Suricata is a network Intrusion Detection System, Intrusion Prevention System and Network Security Monitoring engine. Starting in version 8.0.0 and prior to version 8.0.5, Suricata's IP defragmentation code could deadlock when processing fragmented traffic containing an encapsulated tunnel protocol whose payload is itself fragmented. Version 8.0.5 contains a fix. No known workarounds are available. |
| containerd is an open-source container runtime. Prior to versions 1.7.36, 2.0.13, 2.2.9, 2.3.6, and 2.4.1, a crafted OCI index graph can force very high CPU/memory usage during PullImage (before container start), causing long ContainerCreating stalls and, at larger sizes, node/runtime instability. Versions 1.7.36, 2.0.13, 2.2.9, 2.3.6, and 2.4.1 fix the issue. |
| radare2 is a UNIX-like reverse engineering framework and command-line toolset. Prior to 6.2.0, radare2's NE relocation fixup-chain parser was vulnerable because the NE relocation parser followed fixup chains without an active iteration limit or cycle detection. The vulnerability is triggered by opening a crafted NE executable whose in-bounds relocation entry points back to itself instead of reaching 0xffff. The parser repeatedly processed the same relocation and allocated another relocation object on each iteration. This can cause denial of service through continuous CPU and memory consumption. This issue is fixed in version 6.2.0. |
| In the Linux kernel, the following vulnerability has been resolved:
i3c: master: svc: Prevent IRQ storm from false SLVSTART on NPCM845
On NPCM845, when a target on the I3C bus gets stuck holding SDA low,
the controller reports a false Master Request (MR) in-band interrupt
event. The driver handles this by emitting a STOP condition to restore
the bus.
However, the hardware quirk SVC_I3C_QUIRK_FALSE_SLVSTART indicates that
emitting a STOP condition may spuriously set the SLVSTART interrupt
status bit. In the Master Request case, this creates a feedback loop:
the STOP triggers a new SLVSTART event, the IRQ handler fires again,
the controller still reports an MR type, another STOP is emitted, and
the cycle repeats indefinitely, resulting in an IRQ storm that can lock
up the CPU.
Clear the SLVSTART status bit explicitly after emitting the STOP in the
Master Request IBI handler when the SVC_I3C_QUIRK_FALSE_SLVSTART quirk
is set. This breaks the feedback loop without affecting normal SLVSTART
processing, which is already guarded in the top-level IRQ handler by
checking that MSTATUS is in SLVREQ state. |
| OpenEXR is the reference implementation and specification for the EXR image format, widely used in the motion picture industry. Versions prior to 3.2.10, 3.3.12, and 3.4.13 contain an infinite-loop vulnerability in SampleCountChannel. The helper roundListSizeUp() rounds a sample-list size up to the next power of two using repeated unsigned left shifts, which terminates for normal values but fails for UINT_MAX: the sequence reaches 0x80000000, and the next left shift wraps the 32-bit value to 0. Because 0 remains less than UINT_MAX, the loop never progresses and never exits. The bug is reachable through public OpenEXRUtil APIs, either by editing the sample-count buffer through SampleCountChannel::Edit (whose destructor calls endEdit()) or by calling SampleCountChannel::set(x, y, UINT_MAX) on a valid pixel. This issue has been fixed in versions 3.2.10, 3.3.12, and 3.4.13. |
| In the Linux kernel, the following vulnerability has been resolved:
af_unix: Update last skb marker in manage_oob().
Fahad Alharbi reported that blocking recv(MSG_PEEK) could hog CPU
due to OOB skb.
In the following cases, manage_oob() skips OOB skb(s) and returns
NULL for the last recv(MSG_PEEK):
socketpair(AF_UNIX, SOCK_STREAM, 0, sk);
1) skb -> OOB skb -> NULL
send(sk[0], "ab", 2, MSG_OOB);
recv(sk[1], buf, 0, MSG_PEEK);
2) skb -> consumed OOB skb -> NULL
send(sk[0], "ab", 2, MSG_OOB);
recv(sk[1], buf, 1, MSG_OOB);
recv(sk[1], buf, 0, MSG_PEEK);
3) consumed OOB skb -> OOB skb -> NULL
send(sk[0], "a", 1, MSG_OOB);
recv(sk[1], buf, 0, MSG_OOB);
send(sk[0], "b", 1, MSG_OOB);
recv(sk[1], buf, 1, MSG_PEEK);
Then, @copied is 0 in unix_stream_read_generic() (zero-length buffer,
or non-OOB skb is not yet consumed), and unix_stream_data_wait() is
called.
However, it returns immediately because @last is not updated in
unix_stream_read_generic(), and the thread busy-waits for a new skb.
Let's update @last in manage_oob().
For MSG_PEEK, @last is updated with the skipped OOB, and for the
non-peek case, @last matches the returned value (when !copied)
because OOB is unlinked.
Note that manage_oob() is inlined and no stack canary is added. |
| radare2 is a UNIX-like reverse engineering framework and command-line toolset. Prior to 6.2.0, radare2's Apple Preferred Executable Format loader was vulnerable because the PEF loader accepted relocSecCount values that were not bounded by the number of sections or complete relocation records in the input. The vulnerability is triggered by normal binary-format auto-detection of a small crafted Apple PEF file. The loader could perform up to 268,435,456 relocation-section iterations and repeated buffer operations after record offsets passed the end of the file. This can cause denial of service through excessive CPU consumption and prolonged processing. This issue is fixed in version 6.2.0. |
| In the Linux kernel, the following vulnerability has been resolved:
net: net_failover: Fix the deadlock in net_failover_slave_name_change()
This is a sibling fix of commit
b84c5632c7b3 ("net: net_failover: Fix the deadlock in slave register").
There is netdev_lock_ops() in the upper callers, so using netif_open()
instead of dev_open().
Call Trace:
__schedule+0x2bb/0x650
schedule+0x27/0xb0
schedule_preempt_disabled+0x15/0x30
__mutex_lock.constprop.0+0x550/0xaf0
__mutex_lock_slowpath+0x13/0x20
mutex_lock+0x3b/0x50
dev_open+0x3b/0xe0
net_failover_slave_name_change+0x22/0x40
failover_event+0xd4/0x1e0
notifier_call_chain+0x62/0xf0
raw_notifier_call_chain+0x16/0x30
call_netdevice_notifiers_info+0x50/0x80
netif_change_name+0x200/0x330
do_setlink.isra.0+0xb12/0xdf0
? security_capable+0x9a/0x1e0
? ns_capable+0x31/0x60
rtnl_setlink+0x302/0x670
? netlink_recvmsg+0x296/0x340
? security_capable+0x9a/0x1e0
? __pfx_rtnl_setlink+0x10/0x10
rtnetlink_rcv_msg+0x384/0x460
? __pfx_rtnetlink_rcv_msg+0x10/0x10
netlink_rcv_skb+0x61/0x120
rtnetlink_rcv+0x15/0x30
netlink_unicast+0x28f/0x3c0
netlink_sendmsg+0x216/0x450
__sys_sendto+0x222/0x230
__x64_sys_sendto+0x24/0x40
x64_sys_call+0x1d5d/0x2390
do_syscall_64+0x105/0x5a0
? do_syscall_64+0x140/0x5a0
? exc_page_fault+0x94/0x1e0
entry_SYSCALL_64_after_hwframe+0x76/0x7e |
| Uncontrolled Resource Consumption (CWE-400 / CWE-407) in the ANTLR 3 search query parser (QueryParser / Query.g) in Gerrit Code Review versions 2.0.19 through 3.12.9, 3.13.0 through 3.13.8, and 3.14.0 through 3.14.2 allows an unauthenticated remote attacker (or an authenticated user if anonymous read access is disabled) to cause a persistent denial of service (CPU exhaustion and HTTP worker thread pool starvation requiring a server restart) via crafted search queries containing deeply nested parentheses sent to query evaluation endpoints (/changes/?q=, /accounts/?q=, /groups/?query=, /projects/?query=, /Documentation/?q=, /changes/{id}/query?expression=, or SSH gerrit query). Because syntactic predicates in conditionOr and conditionAnd recurse via conditionBase without memoization prior to capability or visibility checks and worker threads do not abort when the client disconnects, a small number of requests (such as 25 requests matching default httpd.maxThreads) can permanently pin all HTTP worker threads. This issue is fixed in Gerrit Code Review versions 3.12.10, 3.13.9, and 3.14.3. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: f_tcm: fix deadlock in usbg_make_tpg()
usbg_make_tpg() held dep_lock while calling
configfs_depend_item_unlocked(), which acquires the configfs root
inode lock when operating across subsystems. This creates a circular
lock dependency with configfs_rmdir():
dep_lock -> configfs root inode lock -> su_mutex -> dep_lock
In usbg_make_tpg(), dep_lock only serialized the read of opts->ready,
which is a monotonic flag that transitions from false to true exactly
once (in tcm_set_name()) and never reverts. Remove dep_lock from
usbg_make_tpg() entirely and use READ_ONCE/WRITE_ONCE to access
opts->ready locklessly instead. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: fix circular lock dependency in ext4_ext_migrate
Move iput(tmp_inode) after ext4_writepages_up_write() to avoid a
circular lock dependency between s_writepages_rwsem and sb_internal
(freeze protection).
The deadlock scenario:
CPU0 (EXT4_IOC_MIGRATE) CPU1 (orphan cleanup during mount)
---- ----
ext4_ext_migrate()
ext4_writepages_down_write()
s_writepages_rwsem (write)
ext4_evict_inode()
sb_start_intwrite() [sb_internal]
...
ext4_writepages()
s_writepages_rwsem (read) [BLOCKED]
iput(tmp_inode)
ext4_evict_inode()
sb_start_intwrite() [BLOCKED]
The tmp_inode is a temporary inode with nlink=0 created solely for
building the extent tree. Its eviction does not require
s_writepages_rwsem protection, so deferring iput() until after
releasing the rwsem is safe. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: skip extra isize expansion during mount to prevent deadlock
ext4_try_to_expand_extra_isize() is called from __ext4_mark_inode_dirty()
while holding an active jbd2 handle. During mount (!SB_ACTIVE), the
expand path may move xattrs to external blocks and release ea_inodes via
iput(). When !SB_ACTIVE, iput() calls write_inode_now() which acquires
s_writepages_rwsem, creating a circular lock dependency:
s_writepages_rwsem --> jbd2_handle --> xattr_sem --> s_writepages_rwsem
This can be triggered via:
ext4_process_orphan() -> ext4_truncate() -> ext4_mark_inode_dirty()
-> ext4_try_to_expand_extra_isize()
or:
ext4_evict_inode() -> ext4_mark_inode_dirty()
-> ext4_try_to_expand_extra_isize()
Skip expansion when !SB_ACTIVE. This is a minor loss of functionality
(extra isize won't grow for these inodes during mount), which e2fsck
can resolve later if needed. |
| Velociraptor contains a deadlock condition that may be triggered by authenticated users. The issue stems from a lock management bug in the user management module. |
