| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: xfrm_interface: require CAP_NET_ADMIN in the device netns for changelink
xfrmi_changelink() operates on at most two netns, dev_net(dev) and the
interface link netns xi->net. They differ once the device is created in
or moved to a netns other than the one the request runs in. The rtnl
changelink path checks CAP_NET_ADMIN only against dev_net(dev), so a
caller privileged there but not in xi->net can rewrite an interface that
lives in xi->net.
Gate xfrmi_changelink() on rtnl_dev_link_net_capable() at its top,
before any attribute is parsed. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: arm64: nv: Drop bogus WARN for write to ZCR_EL2
It is entirely possible for a guest to write to the ZCR_EL2 sysreg alias
while in a nested context, as it is expected if FEAT_NV2 is advertised
to the L1 hypervisor.
Get rid of the bogus WARN which, since the hyp vectors were installed at
this point, has the effect of a hyp_panic... |
| In the Linux kernel, the following vulnerability has been resolved:
mm/hugetlb: fix hugetlb cgroup rsvd charge/uncharge mismatch
In alloc_hugetlb_folio(), a single h_cg pointer is used for both the rsvd
and non-rsvd hugetlb cgroup charges. When map_chg is set,
hugetlb_cgroup_charge_cgroup_rsvd() stores the charged cgroup in h_cg, but
the immediately following hugetlb_cgroup_charge_cgroup() overwrites h_cg
with the non-rsvd cgroup pointer.
As a result, hugetlb_cgroup_commit_charge_rsvd() stores the wrong
(non-rsvd) cgroup pointer into the folio's rsvd slot.
When the folio is later freed, free_huge_folio() unconditionally calls
both hugetlb_cgroup_uncharge_folio() and
hugetlb_cgroup_uncharge_folio_rsvd(). The rsvd uncharge reads back the
wrong cgroup from the folio and decrements a counter that was never
charged for that cgroup, causing a page_counter underflow:
page_counter underflow: -512 nr_pages=512
WARNING: mm/page_counter.c:61 at page_counter_cancel
Fix this by introducing a separate h_cg_rsvd pointer exclusively for the
rsvd charge path, keeping the rsvd and non-rsvd charges fully independent
through their charge, commit, and error uncharge paths. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: SOF: ipc3-control: Use overflow checks in control_update size calc
In sof_ipc3_control_update(), the expected_size calculation uses
firmware-provided cdata->num_elems in arithmetic that could overflow
on 32-bit platforms, wrapping to a small value. This would allow the
cdata->rhdr.hdr.size comparison to pass with mismatched sizes,
potentially leading to out-of-bounds access in snd_sof_update_control.
Use check_mul_overflow() and check_add_overflow() to detect and reject
overflowed size calculations. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: close durable scavenger races against m_fp_list lookups
ksmbd_durable_scavenger() has two related races against any walker
that iterates f_ci->m_fp_list, including ksmbd_lookup_fd_inode()
(used by ksmbd_vfs_rename) and the share-mode checks in
fs/smb/server/smb_common.c.
(1) fp->node list-head reuse. Durable-preserved handles can remain
linked on f_ci->m_fp_list after session teardown so share-mode checks
still see them while the handle is reconnectable. The scavenger
collected expired handles by adding fp->node to a local
scavenger_list after removing them from the global durable idr.
Because fp->node is the same list_head used by m_fp_list,
list_add(&fp->node, &scavenger_list) overwrites the m_fp_list links
and corrupts both lists. CONFIG_DEBUG_LIST can report this on the
share-mode walk path.
(2) Refcount race against m_fp_list walkers. The scavenger qualifies
an expired durable handle with atomic_read(&fp->refcount) > 1 and
fp->conn under global_ft.lock, removes fp from global_ft, then drops
global_ft.lock before unlinking fp from m_fp_list and freeing it.
During that gap fp is still linked on m_fp_list with f_state ==
FP_INITED. ksmbd_lookup_fd_inode() under m_lock read calls
ksmbd_fp_get() (atomic_inc_not_zero on refcount that is still 1) and
takes a live reference; the scavenger then unlinks and frees fp
while the holder owns a reference, leading to UAF on the holder's
subsequent ksmbd_fd_put() and on any field reads performed by a
concurrent share-mode walker that iterates m_fp_list without taking
ksmbd_fp_get() (smb_check_perm_dleases-like paths).
Fix both:
* Stop reusing fp->node as a scavenger-private list node. Remove
one expired handle from global_ft under global_ft.lock, take an
explicit transient reference, drop the lock, unlink fp->node
from m_fp_list under f_ci->m_lock, then drop both the durable
lifetime and transient references with atomic_sub_and_test(2,
&fp->refcount). If the scavenger is the last putter the close
runs there; otherwise an in-flight holder that already raced
through the m_fp_list lookup owns the final close via its
ksmbd_fd_put() path. The one-at-a-time disposal can rescan the
durable idr when multiple handles expire in the same pass, but
durable scavenging is a background expiration path and the final
full scan recomputes min_timeout before the next wait.
* Clear fp->persistent_id inside __ksmbd_remove_durable_fd() right
after idr_remove(), so a delayed final close from a holder that
snatched fp does not re-issue idr_remove() on a persistent id
that idr_alloc_cyclic() in ksmbd_open_durable_fd() may have
already handed out to a brand-new durable handle.
* Bypass the per-conn open_files_count decrement in
__put_fd_final() when fp is detached from any session table
(fp->conn cleared by session_fd_check() at durable preserve --
paired with the volatile_id clear at unpublish, so checking
fp->conn alone is sufficient). The walker that owns the final
close runs from an unrelated work->conn whose
stats.open_files_count never tracked this durable fp; without
this guard the holder would underflow that unrelated counter.
The two races are folded into one patch because patch (1) alone
cleans up the corrupted list but leaves a deterministic UAF window
for m_fp_list walkers that the transient-reference and
persistent_id discipline in (2) close; bisecting onto an
intermediate state would land on a UAF that pre-patch chaos merely
made less reproducible.
Validation:
* CONFIG_DEBUG_LIST coverage for the list_head reuse path.
* KASAN-enabled direct SMB2 durable-handle coverage that exercised
ksmbd_durable_scavenger() and non-NULL ksmbd_lookup_fd_inode()
returns while durable handles expired under concurrent rename
lookups, with no KASAN, UAF, list-corruption, ODEBUG, or WARNING
reports.
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
platform/x86: uniwill-laptop: Do not enable the charging limit even when forced
It seems that on some older models (~2020) the battery charging limit
can permanently damage the battery. Prevent users from enabling this
feature thru the "force" module parameter to avoid causing permanent
hardware damage on such devices. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: btmtk: fix urb->setup_packet leak in error paths
The setup_packet of control urb is not freed if usb_submit_urb fails or
the submitted urb is killed. Add free in these two paths. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: wilc1000: fix dma_buffer leak on bus acquire failure
wilc_wlan_firmware_download() allocates dma_buffer with kmalloc() at
the top of the function and uses a 'fail:' label to free it via
kfree(dma_buffer) on error.
All later error paths correctly use 'goto fail' to route through this
cleanup. However, the early failure path after the first acquire_bus()
call uses a bare 'return ret;', which leaks dma_buffer whenever the bus
acquire fails.
Replace the early return with goto fail so the existing cleanup path
runs.
Found via a custom Coccinelle semantic patch hunting for kmalloc'd
locals leaked on early-return error paths in driver firmware-download
code. |
| In the Linux kernel, the following vulnerability has been resolved:
pds_core: fix debugfs_lookup dentry leak and error handling
debugfs_lookup() returns a dentry with an elevated reference count that
must be released with dput(). The current code discards the returned
dentry without calling dput(), causing a reference leak on every
firmware reset recovery.
Additionally, when CONFIG_DEBUG_FS is disabled, debugfs_lookup()
returns ERR_PTR(-ENODEV), not NULL. The current check passes for error
pointers and would call dput() on an invalid pointer, causing a crash. |
| In the Linux kernel, the following vulnerability has been resolved:
fbdev: modedb: fix a possible UAF in fb_find_mode()
If mode_option is NULL, it is assigned from mode_option_buf:
if (!mode_option) {
fb_get_options(NULL, &mode_option_buf);
mode_option = mode_option_buf;
}
Later, name is assigned from mode_option:
const char *name = mode_option;
However, mode_option_buf is freed before name is no longer used:
kfree(mode_option_buf);
while name is still accessed by:
if ((name_matches(db[i], name, namelen) ||
Since name aliases mode_option_buf, this may result in a
use-after-free.
Fix this by extending the lifetime of mode_option_buf until the end of the
function by using scope-based resource management for cleanup. |
| In the Linux kernel, the following vulnerability has been resolved:
accel/amdxdna: Fix use-after-free in amdxdna_gem_dmabuf_mmap()
When vm_insert_pages() fails, the error path calls vma->vm_ops->close(vma)
which internally calls drm_gem_vm_close() → drm_gem_object_put(),
releasing the GEM object reference acquired at the start of the function.
However, the close_vma label then falls through to put_obj, which calls
drm_gem_object_put() a second time on the same object.
If the first put releases the last reference, the object is freed and the
second put accesses freed memory, causing a use-after-free.
Fix by returning directly from close_vma instead of falling through to
put_obj, since the close handler already performs all necessary cleanup
including the object put. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/ntfs3: bound copy_lcns dp->page_lcns[] index in analysis pass
In log_replay()'s analysis pass, after find_dp() returns a
valid DIR_PAGE_ENTRY for the (target_attr, target_vcn) tuple,
the copy_lcns block walks lrh->lcns_follow further entries:
t16 = le16_to_cpu(lrh->lcns_follow);
for (i = 0; i < t16; i++) {
size_t j = (size_t)(le64_to_cpu(lrh->target_vcn) -
le64_to_cpu(dp->vcn));
dp->page_lcns[j + i] = lrh->page_lcns[i];
}
find_dp() only validates that target_vcn falls within
[dp->vcn, dp->vcn + dp->lcns_follow), i.e., that the FIRST
cluster is covered. The walk through the further entries is
not bounded against dp->lcns_follow. For a malformed LRH
where target_vcn = dp->vcn + dp->lcns_follow - 1 and
lrh->lcns_follow > 1, the i > 0 writes overflow the dp's
allocated page_lcns[] array.
Add the missing j + lrh->lcns_follow <= dp->lcns_follow guard.
Reproduced under UML+KASAN on mainline 8d90b09e6741 as a
slab-out-of-bounds write of size 8 from log_replay+0x68d4 on
the mount path.
This is distinct from Pavitra Jha's 2026-05-02 patch
("fs/ntfs3: validate lcns_follow in log_replay conversion",
<20260502154252.164586-1-jhapavitra98@gmail.com>) which
addresses the separate version-0 dirty-page-table conversion
path's memmove(&dp->vcn, ...) call. The two fixes are
complementary; both should land.
[almaz.alexandrovich@paragon-software.com: clang-formatted the changes,
fixed conflicts] |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: tt: prevent TVLV OOB check overflow
A TT unicast TVLV contains the number of VLANs stored in it. This number is
an u16 and gets multiplied by the size of the struct
batadv_tvlv_tt_vlan_data (8 bytes). The size can therefore overflow the u16
used to store the tt_vlan_len. All additional safety checks to prevent
out-of-bounds access of the TVLV buffer are invalid due to this overflow.
Using size_t prevents this overflow and ensures that the safety checks
compare against the actual buffer requirements. |
| In affected versions of Octopus Deploy Insufficient checks on the project trigger actions allows an unauthorized user to trigger a deployment. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_conntrack_reasm: guard mac_header adjustment after IPv6 defrag
nf_ct_frag6_reasm() slides the packet head forward to drop the IPv6
fragment header and then unconditionally advances skb->mac_header:
skb->mac_header += sizeof(struct frag_hdr);
On the NF_INET_LOCAL_OUT defrag path the skb has no link-layer header
yet, so skb->mac_header is still the "not set" sentinel (u16)~0U. Adding
sizeof(struct frag_hdr) wraps it to a small value (0xffff + 8 == 7),
after which skb_mac_header_was_set() wrongly reports a MAC header is
present and skb_mac_header() points into the headroom.
The reassembler has done this unconditional add since it was introduced;
it was harmless while mac_header was a bare pointer, but wrong once
mac_header became a u16 offset whose unset state is the ~0U sentinel
tested by skb_mac_header_was_set(). The sibling net/ipv6/reassembly.c
does the same relocation and does guard the adjustment; mirror the
guard here. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: arm64: nv: Inject SEA if guest VNCR isn't normal memory
When constructing an L1 VNCR mapping, KVM unconditionally uses cacheable
memory attributes, even if the underlying PFN isn't memory. This gets
particularly hairy if the endpoint doesn't support cacheable memory
attributes, potentially throwing an SError on writeback...
While KVM does permit cacheable memory attributes on certain PFNMAP
VMAs, kvm_translate_vncr() isn't currently grabbing the VMA. So do the
simpler thing for now and just reject everything that isn't memory. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: arm64: nv: Respect read-only PFN when mapping L1 VNCR
KVM currently maps the L1 VNCR into the host stage-1 by relying entirely
on the permissions of the guest stage-1. At the same time, it is
entirely possible that the backing PFN is read-only (e.g. RO memslot),
meaning that the L1 VNCR should use at most a read-only mapping.
Cache the writability of the PFN in the VNCR TLB and use it to constrain
the resulting fixmap permissions. Promote VNCR permission faults to an
SEA in the case where the guest attempts to write to a read-only
endpoint. Conveniently, this also plugs a page leak found by Sashiko [*]
resulting from the early return for a read-only PFN. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: x86: Ignore pending PV EOI if the vCPU has since disabled PV EOIs
Ignore KVM's internal "service pending PV EOI" request if the vCPU has
disabled PV EOIs since the request was made. Asserting that PV EOIs are
enabled can fail if reading guest memory in pv_eoi_get_user() fails, i.e.
if pv_eoi_test_and_clr_pending() bails early, *and* the vCPU also disables
PV EOIs.
kernel BUG at arch/x86/kvm/lapic.c:3338!
Oops: invalid opcode: 0000 [#1] SMP
CPU: 4 UID: 1000 PID: 890 Comm: pv_eoi_test Not tainted 7.0.0-d585aa5894d8-vm #337 PREEMPT
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
RIP: 0010:kvm_lapic_sync_from_vapic+0x12b/0x140 [kvm]
Call Trace:
<TASK>
kvm_arch_vcpu_ioctl_run+0x1075/0x1c30 [kvm]
kvm_vcpu_ioctl+0x2d5/0x980 [kvm]
__x64_sys_ioctl+0x8a/0xd0
do_syscall_64+0xb5/0xb40
entry_SYSCALL_64_after_hwframe+0x4b/0x53
</TASK>
Modules linked in: kvm_intel kvm irqbypass
---[ end trace 0000000000000000 ]--- |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: TC, skip peer flow cleanup when LAG seq is unavailable
mlx5_lag_get_dev_seq() will return error when the peer isn't in the LAG
or when no device is marked as master. Result bad memory access and kernel
crash[1].
Hence, skip the peer when lookup fails.
Note: In case there are peer flows, they are cleaned before LAG cleared
the master mark.
[1]
RIP: 0010:mlx5e_tc_del_fdb_peers_flow+0x3d/0x350 [mlx5_core]
Call Trace:
<TASK>
mlx5e_tc_clean_fdb_peer_flows+0xc1/0x130 [mlx5_core]
mlx5_esw_offloads_unpair+0x3a/0x400 [mlx5_core]
mlx5_esw_offloads_devcom_event+0xee/0x360 [mlx5_core]
mlx5_devcom_send_event+0x7a/0x140 [mlx5_core]
mlx5_esw_offloads_devcom_cleanup+0x2f/0x90 [mlx5_core]
mlx5e_tc_esw_cleanup+0x28/0xf0 [mlx5_core]
mlx5e_rep_tc_cleanup+0x19/0x30 [mlx5_core]
mlx5e_cleanup_uplink_rep_tx+0x36/0x40 [mlx5_core]
mlx5e_cleanup_rep_tx+0x55/0x60 [mlx5_core]
mlx5e_detach_netdev+0x96/0xf0 [mlx5_core]
mlx5e_netdev_change_profile+0x5b/0x120 [mlx5_core]
mlx5e_netdev_attach_nic_profile+0x1b/0x30 [mlx5_core]
mlx5e_vport_rep_unload+0xdd/0x110 [mlx5_core]
__esw_offloads_unload_rep+0x81/0xb0 [mlx5_core]
mlx5_eswitch_unregister_vport_reps+0x1d7/0x220 [mlx5_core]
mlx5e_rep_remove+0x22/0x30 [mlx5_core]
device_release_driver_internal+0x194/0x1f0
bus_remove_device+0xe8/0x1b0
device_del+0x159/0x3c0
mlx5_rescan_drivers_locked+0xbc/0x2d0 [mlx5_core]
mlx5_unregister_device+0x54/0x80 [mlx5_core]
mlx5_uninit_one+0x73/0x130 [mlx5_core]
remove_one+0x78/0xe0 [mlx5_core]
pci_device_remove+0x39/0xa0 |
| In the Linux kernel, the following vulnerability has been resolved:
net: mvneta: re-enable percpu interrupt on resume
On Marvell MPIC platforms (Armada 370/XP/38x), mvneta uses a percpu
IRQ disable/enable scheme for NAPI: the ISR (mvneta_percpu_isr) calls
disable_percpu_irq() to mask the MPIC per-CPU interrupt and schedules
NAPI poll, which calls enable_percpu_irq() on completion to unmask.
If suspend occurs while NAPI poll is pending (between
disable_percpu_irq in the ISR and enable_percpu_irq in poll
completion), the interrupt is never re-enabled:
1. mvneta_percpu_isr: disable_percpu_irq() + napi_schedule()
=> MPIC masked, percpu_enabled cpumask bit cleared
2. NAPI poll does not complete before suspend proceeds
(on PREEMPT_RT this is highly likely since softirqs run in
ksoftirqd which gets frozen; on non-RT it can happen when
softirq processing is deferred to ksoftirqd)
3. mvneta_stop_dev => napi_disable(): cancels the pending poll
without executing the completion path
4. suspend_device_irqs => IRQCHIP_MASK_ON_SUSPEND: masks MPIC
(already masked, but records IRQS_SUSPENDED)
5. Resume: mpic_resume checks irq_percpu_is_enabled() => false
(bit was cleared in step 1) => skips unmask
6. mvneta_start_dev only restores device-level INTR_NEW_MASK,
does not touch the MPIC per-CPU mask
Result: MPIC per-CPU interrupt stays masked permanently. The NIC
generates interrupts (INTR_NEW_CAUSE != 0) but the CPU never
receives them, causing complete loss of network connectivity.
Fix by calling on_each_cpu(mvneta_percpu_enable) in the resume path
to unconditionally unmask the MPIC per-CPU interrupt regardless of
pre-suspend state. |
