| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: lzo: reject compressed segment that overflows the compressed input
lzo_decompress_bio() validates each on-disk segment length seg_len only
against the workspace cbuf size, not against the compressed input size
(compressed_len, the total folio bytes of the bio). A crafted extent can
carry a segment whose seg_len passes the cbuf check but runs past the end
of the bio, so copy_compressed_segment() walks off the last folio:
get_current_folio() then returns the NULL folio from bio_next_folio(), and
with CONFIG_BTRFS_ASSERT disabled (default) folio_size(NULL) faults.
BUG: KASAN: null-ptr-deref in lzo_decompress_bio (fs/btrfs/lzo.c:383)
Read of size 8 at addr 0000000000000000 by task kworker/u8:1/29
Workqueue: btrfs-endio simple_end_io_work
kasan_report (mm/kasan/report.c:590)
lzo_decompress_bio (fs/btrfs/lzo.c:383)
end_bbio_compressed_read (fs/btrfs/compression.c:1065)
btrfs_bio_end_io (fs/btrfs/bio.c:135)
btrfs_check_read_bio (fs/btrfs/bio.c:180 fs/btrfs/bio.c:285)
simple_end_io_work
process_one_work
worker_thread
Reject any segment whose payload would extend beyond compressed_len before
copying it, treating it as corruption like the other on-disk validation
failures in this function. |
| In the Linux kernel, the following vulnerability has been resolved:
octeontx2-af: npc: Fix size of entry2cntr_map
KASAN prints below splat. This is caused by allocating counter for
reserved mcam entry for cpt 2nd pass entry. But mcam->entry2cntr_map
is not allocated for reserved entries.
BUG: KASAN: slab-out-of-bounds in npc_map_mcam_entry_and_cntr+0xb0/0x1a0
Write of size 2 at addr ffff0001033e7ffe by task kworker/0:1/14
CPU: 0 PID: 14 Comm: kworker/0:1 Not tainted 6.1.67 #1
Hardware name: Marvell CN106XX board (DT)
Workqueue: events work_for_cpu_fn
Call trace:
dump_backtrace.part.0+0xe4/0xf0
show_stack+0x18/0x30
dump_stack_lvl+0x88/0xb4
print_report+0x154/0x458
kasan_report+0xb8/0x194
__asan_store2+0x7c/0xa0
npc_map_mcam_entry_and_cntr+0xb0/0x1a0
rvu_mbox_handler_npc_mcam_write_entry+0x268/0x280
npc_install_flow+0x840/0xfe0
rvu_npc_install_cpt_pass2_entry+0x138/0x190
rvu_nix_init+0x148c/0x2880
rvu_probe+0x1800/0x30b0
local_pci_probe+0x78/0xe0
work_for_cpu_fn+0x30/0x50
process_one_work+0x4cc/0x97c
worker_thread+0x360/0x630
kthread+0x1a0/0x1b0
ret_from_fork+0x10/0x20 |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: seq: oss: Serialize readq reset state with q->lock
snd_seq_oss_readq_clear() resets qlen, head, and tail without
q->lock even though the normal reader and producer paths serialize the
same ring state under that spinlock. A reset can therefore race
snd_seq_oss_readq_free() or snd_seq_oss_readq_put_event() and leave
stale records in the queue, drop freshly queued ones, or report the
wrong readiness after wakeup. KCSAN reports a data race between
snd_seq_oss_readq_clear() and snd_seq_oss_readq_free().
Take q->lock while clearing the ring and resetting input_time. Factor
the enqueue logic into a caller-locked helper so
snd_seq_oss_readq_put_timestamp() updates its suppression state under
the same lock instead of racing the reset path.
The buggy scenario involves two paths, with each column showing the
order within that path:
reset path: locked readq updater:
1. snd_seq_oss_reset() or 1. A reader or callback producer
release reaches takes q->lock on the same queue.
snd_seq_oss_readq_clear().
2. snd_seq_oss_readq_clear() 2. The updater tests or modifies
resets qlen, head, tail, qlen, head, and tail.
and input_time.
3. snd_seq_oss_readq_clear() 3. The updater completes its
wakes sleepers on read-modify-write sequence.
q->midi_sleep.
4. Without q->lock, the reset 4. The resulting ring state drives
can overlap the locked later reads and readiness.
update.
KCSAN reports:
BUG: KCSAN: data-race in snd_seq_oss_readq_clear /
snd_seq_oss_readq_free
write to 0xffff8881069fe608 of 4 bytes by task 120516 on cpu 0:
snd_seq_oss_readq_free+0x6c/0x80
snd_seq_oss_read+0xcb/0x250
odev_read+0x38/0x60
vfs_read+0xff/0x600
ksys_read+0xb4/0x140
__x64_sys_read+0x46/0x60
do_syscall_64+0xbb/0x2f0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
read to 0xffff8881069fe608 of 4 bytes by task 120517 on cpu 1:
snd_seq_oss_readq_clear+0x1f/0x90
snd_seq_oss_reset+0xa7/0xf0
snd_seq_oss_ioctl+0x6f6/0x7e0
odev_ioctl+0x56/0xc0
__x64_sys_ioctl+0xd1/0x120
do_syscall_64+0xbb/0x2f0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
value changed: 0x00000001 -> 0x00000000 |
| Improper validation of array index vulnerability in Velneo vServer. This issue affects vServer: from 36.0 before 36.6 and from 37.0 before 37.2. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: Skip vcn poison irq release on VF
VF doesn't enable VCN poison irq in VCNv2.5. Skip releasing it and avoid
call trace during deinitialization.
[ 71.913601] [drm] clean up the vf2pf work item
[ 71.915088] ------------[ cut here ]------------
[ 71.915092] WARNING: CPU: 3 PID: 1079 at /tmp/amd.aFkFvSQl/amd/amdgpu/amdgpu_irq.c:641 amdgpu_irq_put+0xc6/0xe0 [amdgpu]
[ 71.915355] Modules linked in: amdgpu(OE-) amddrm_ttm_helper(OE) amdttm(OE) amddrm_buddy(OE) amdxcp(OE) amddrm_exec(OE) amd_sched(OE) amdkcl(OE) drm_suballoc_helper drm_display_helper cec rc_core i2c_algo_bit video wmi binfmt_misc nls_iso8859_1 intel_rapl_msr intel_rapl_common input_leds joydev serio_raw mac_hid qemu_fw_cfg sch_fq_codel dm_multipath scsi_dh_rdac scsi_dh_emc scsi_dh_alua efi_pstore ip_tables x_tables autofs4 btrfs blake2b_generic raid10 raid456 async_raid6_recov async_memcpy async_pq async_xor async_tx xor raid6_pq libcrc32c raid1 raid0 hid_generic crct10dif_pclmul crc32_pclmul polyval_clmulni polyval_generic ghash_clmulni_intel usbhid 8139too sha256_ssse3 sha1_ssse3 hid psmouse bochs i2c_i801 ahci drm_vram_helper libahci i2c_smbus lpc_ich drm_ttm_helper 8139cp mii ttm aesni_intel crypto_simd cryptd
[ 71.915484] CPU: 3 PID: 1079 Comm: rmmod Tainted: G OE 6.8.0-87-generic #88~22.04.1-Ubuntu
[ 71.915489] Hardware name: Red Hat KVM/RHEL, BIOS 1.16.3-2.el9_5.1 04/01/2014
[ 71.915492] RIP: 0010:amdgpu_irq_put+0xc6/0xe0 [amdgpu]
[ 71.915768] Code: 75 84 b8 ea ff ff ff eb d4 44 89 ea 48 89 de 4c 89 e7 e8 fd fc ff ff 5b 41 5c 41 5d 41 5e 5d 31 d2 31 f6 31 ff e9 55 30 3b c7 <0f> 0b eb d4 b8 fe ff ff ff eb a8 e9 b7 3b 8a 00 66 2e 0f 1f 84 00
[ 71.915771] RSP: 0018:ffffcf0800eafa30 EFLAGS: 00010246
[ 71.915775] RAX: 0000000000000000 RBX: ffff891bda4b0668 RCX: 0000000000000000
[ 71.915777] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
[ 71.915779] RBP: ffffcf0800eafa50 R08: 0000000000000000 R09: 0000000000000000
[ 71.915781] R10: 0000000000000000 R11: 0000000000000000 R12: ffff891bda480000
[ 71.915782] R13: 0000000000000000 R14: 0000000000000001 R15: 0000000000000000
[ 71.915792] FS: 000070cff87c4c40(0000) GS:ffff893abfb80000(0000) knlGS:0000000000000000
[ 71.915795] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 71.915797] CR2: 00005fa13073e478 CR3: 000000010d634006 CR4: 0000000000770ef0
[ 71.915800] PKRU: 55555554
[ 71.915802] Call Trace:
[ 71.915805] <TASK>
[ 71.915809] vcn_v2_5_hw_fini+0x19e/0x1e0 [amdgpu] |
| In the Linux kernel, the following vulnerability has been resolved:
drm: renesas: rz-du: mipi_dsi: fix kernel panic when rebooting for some panels
Since commit 56de5e305d4b ("clk: renesas: r9a07g044: Add MSTOP for RZ/G2L")
we may get the following kernel panic, for some panels, when rebooting:
systemd-shutdown[1]: Rebooting.
Call trace:
...
do_serror+0x28/0x68
el1h_64_error_handler+0x34/0x50
el1h_64_error+0x6c/0x70
rzg2l_mipi_dsi_host_transfer+0x114/0x458 (P)
mipi_dsi_device_transfer+0x44/0x58
mipi_dsi_dcs_set_display_off_multi+0x9c/0xc4
ili9881c_unprepare+0x38/0x88
drm_panel_unprepare+0xbc/0x108
This happens for panels that need to send MIPI-DSI commands in their
unprepare() callback. Since the MIPI-DSI interface is stopped at that
point, rzg2l_mipi_dsi_host_transfer() triggers the kernel panic.
Fix by moving rzg2l_mipi_dsi_stop() to new callback function
rzg2l_mipi_dsi_atomic_post_disable().
With this change we now have the correct power-down/stop sequence:
systemd-shutdown[1]: Rebooting.
rzg2l-mipi-dsi 10850000.dsi: rzg2l_mipi_dsi_atomic_disable(): entry
ili9881c-dsi 10850000.dsi.0: ili9881c_unprepare(): entry
rzg2l-mipi-dsi 10850000.dsi: rzg2l_mipi_dsi_atomic_post_disable(): entry
reboot: Restarting system |
| In the Linux kernel, the following vulnerability has been resolved:
ring-buffer: Fix possible dereference of uninitialized pointer
There is a pointer head_page in rb_meta_validate_events() which is not
initialized at the beginning of a function. This pointer can be dereferenced
if there is a failure during reader page validation. In this case the control
is passed to "invalid" label where the pointer is dereferenced in a loop.
To fix the issue initialize orig_head and head_page before calling
rb_validate_buffer.
Found by Linux Verification Center (linuxtesting.org) with SVACE. |
| In the Linux kernel, the following vulnerability has been resolved:
media: chips-media: wave5: Fix Null reference while testing fluster
When multi instances are created/destroyed, many interrupts happens
and structures for decoder are removed.
"struct vpu_instance" this structure is shared for all flow in the decoder,
so if the structure is not protected by lock, Null dereference
could happens sometimes.
IRQ Handler was spilt to two phases and Lock was added as well. |
| In the Linux kernel, the following vulnerability has been resolved:
alpha: fix user-space corruption during memory compaction
Alpha systems can suffer sporadic user-space crashes and heap
corruption when memory compaction is enabled.
Symptoms include SIGSEGV, glibc allocator failures (e.g. "unaligned
tcache chunk"), and compiler internal errors. The failures disappear
when compaction is disabled or when using global TLB invalidation.
The root cause is insufficient TLB shootdown during page migration.
Alpha relies on ASN-based MM context rollover for instruction cache
coherency, but this alone is not sufficient to prevent stale data or
instruction translations from surviving migration.
Fix this by introducing a migration-specific helper that combines:
- MM context invalidation (ASN rollover),
- immediate per-CPU TLB invalidation (TBI),
- synchronous cross-CPU shootdown when required.
The helper is used only by migration/compaction paths to avoid changing
global TLB semantics.
Additionally, update flush_tlb_other(), pte_clear(), to use
READ_ONCE()/WRITE_ONCE() for correct SMP memory ordering.
This fixes observed crashes on both UP and SMP Alpha systems. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: chipidea: udc: fix DMA and SG cleanup in _ep_nuke()
The ChipIdea UDC driver can encounter "not page aligned sg buffer"
errors when a USB device is reconnected after being disconnected
during an active transfer. This occurs because _ep_nuke() returns
requests to the gadget layer without properly unmapping DMA buffers
or cleaning up scatter-gather bounce buffers.
Root cause:
When a disconnect happens during a multi-segment DMA transfer, the
request's num_mapped_sgs field and sgt.sgl pointer remain set with
stale values. The request is returned to the gadget driver with status
-ESHUTDOWN but still has active DMA state. If the gadget driver reuses
this request on reconnect without reinitializing it, the stale DMA
state causes _hardware_enqueue() to skip DMA mapping (seeing non-zero
num_mapped_sgs) and attempt to use freed/invalid DMA addresses,
leading to alignment errors and potential memory corruption.
The normal completion path via _hardware_dequeue() properly calls
usb_gadget_unmap_request_by_dev() and sglist_do_debounce() before
returning the request. The _ep_nuke() path must do the same cleanup
to ensure requests are returned in a clean, reusable state.
Fix:
Add DMA unmapping and bounce buffer cleanup to _ep_nuke() to mirror
the cleanup sequence in _hardware_dequeue():
- Call usb_gadget_unmap_request_by_dev() if num_mapped_sgs is set
- Call sglist_do_debounce() with copy=false if bounce buffer exists
This ensures that when requests are returned due to endpoint shutdown,
they don't retain stale DMA mappings. The 'false' parameter to
sglist_do_debounce() prevents copying data back (appropriate for
shutdown path where transfer was aborted). |
| In the Linux kernel, the following vulnerability has been resolved:
9p/xen: protect xen_9pfs_front_free against concurrent calls
The xenwatch thread can race with other back-end change notifications
and call xen_9pfs_front_free() twice, hitting the observed general
protection fault due to a double-free. Guard the teardown path so only
one caller can release the front-end state at a time, preventing the
crash.
This is a fix for the following double-free:
[ 27.052347] Oops: general protection fault, probably for non-canonical address 0x6b6b6b6b6b6b6b6b: 0000 [#1] SMP DEBUG_PAGEALLOC NOPTI
[ 27.052357] CPU: 0 UID: 0 PID: 32 Comm: xenwatch Not tainted 6.18.0-02087-g51ab33fc0a8b-dirty #60 PREEMPT(none)
[ 27.052363] RIP: e030:xen_9pfs_front_free+0x1d/0x150
[ 27.052368] Code: 90 90 90 90 90 90 90 90 90 90 90 90 90 41 55 41 54 55 48 89 fd 48 c7 c7 48 d0 92 85 53 e8 cb cb 05 00 48 8b 45 08 48 8b 55 00 <48> 3b 28 0f 85 f9 28 35 fe 48 3b 6a 08 0f 85 ef 28 35 fe 48 89 42
[ 27.052377] RSP: e02b:ffffc9004016fdd0 EFLAGS: 00010246
[ 27.052381] RAX: 6b6b6b6b6b6b6b6b RBX: ffff88800d66e400 RCX: 0000000000000000
[ 27.052385] RDX: 6b6b6b6b6b6b6b6b RSI: 0000000000000000 RDI: 0000000000000000
[ 27.052389] RBP: ffff88800a887040 R08: 0000000000000000 R09: 0000000000000000
[ 27.052393] R10: 0000000000000000 R11: 0000000000000000 R12: ffff888009e46b68
[ 27.052397] R13: 0000000000000200 R14: 0000000000000000 R15: ffff88800a887040
[ 27.052404] FS: 0000000000000000(0000) GS:ffff88808ca57000(0000) knlGS:0000000000000000
[ 27.052408] CS: e030 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 27.052412] CR2: 00007f9714004360 CR3: 0000000004834000 CR4: 0000000000050660
[ 27.052418] Call Trace:
[ 27.052420] <TASK>
[ 27.052422] xen_9pfs_front_changed+0x5d5/0x720
[ 27.052426] ? xenbus_otherend_changed+0x72/0x140
[ 27.052430] ? __pfx_xenwatch_thread+0x10/0x10
[ 27.052434] xenwatch_thread+0x94/0x1c0
[ 27.052438] ? __pfx_autoremove_wake_function+0x10/0x10
[ 27.052442] kthread+0xf8/0x240
[ 27.052445] ? __pfx_kthread+0x10/0x10
[ 27.052449] ? __pfx_kthread+0x10/0x10
[ 27.052452] ret_from_fork+0x16b/0x1a0
[ 27.052456] ? __pfx_kthread+0x10/0x10
[ 27.052459] ret_from_fork_asm+0x1a/0x30
[ 27.052463] </TASK>
[ 27.052465] Modules linked in:
[ 27.052471] ---[ end trace 0000000000000000 ]--- |
| In the Linux kernel, the following vulnerability has been resolved:
vhost: move vdpa group bound check to vhost_vdpa
Remove duplication by consolidating these here. This reduces the
posibility of a parent driver missing them.
While we're at it, fix a bug in vdpa_sim where a valid ASID can be
assigned to a group equal to ngroups, causing an out of bound write. |
| In the Linux kernel, the following vulnerability has been resolved:
kcm: fix zero-frag skb in frag_list on partial sendmsg error
Syzkaller reported a warning in kcm_write_msgs() when processing a
message with a zero-fragment skb in the frag_list.
When kcm_sendmsg() fills MAX_SKB_FRAGS fragments in the current skb,
it allocates a new skb (tskb) and links it into the frag_list before
copying data. If the copy subsequently fails (e.g. -EFAULT from
user memory), tskb remains in the frag_list with zero fragments:
head skb (msg being assembled, NOT yet in sk_write_queue)
+-----------+
| frags[17] | (MAX_SKB_FRAGS, all filled with data)
| frag_list-+--> tskb
+-----------+ +----------+
| frags[0] | (empty! copy failed before filling)
+----------+
For SOCK_SEQPACKET with partial data already copied, the error path
saves this message via partial_message for later completion. For
SOCK_SEQPACKET, sock_write_iter() automatically sets MSG_EOR, so a
subsequent zero-length write(fd, NULL, 0) completes the message and
queues it to sk_write_queue. kcm_write_msgs() then walks the
frag_list and hits:
WARN_ON(!skb_shinfo(skb)->nr_frags)
TCP has a similar pattern where skbs are enqueued before data copy
and cleaned up on failure via tcp_remove_empty_skb(). KCM was
missing the equivalent cleanup.
Fix this by tracking the predecessor skb (frag_prev) when allocating
a new frag_list entry. On error, if the tail skb has zero frags,
use frag_prev to unlink and free it in O(1) without walking the
singly-linked frag_list. frag_prev is safe to dereference because
the entire message chain is only held locally (or in kcm->seq_skb)
and is not added to sk_write_queue until MSG_EOR, so the send path
cannot free it underneath us.
Also change the WARN_ON to WARN_ON_ONCE to avoid flooding the log
if the condition is somehow hit repeatedly.
There are currently no KCM selftests in the kernel tree; a simple
reproducer is available at [1].
[1] https://gist.github.com/mrpre/a94d431c757e8d6f168f4dd1a3749daa |
| In the Linux kernel, the following vulnerability has been resolved:
team: avoid NETDEV_CHANGEMTU event when unregistering slave
syzbot is reporting
unregister_netdevice: waiting for netdevsim0 to become free. Usage count = 3
ref_tracker: netdev@ffff88807dcf8618 has 1/2 users at
__netdev_tracker_alloc include/linux/netdevice.h:4400 [inline]
netdev_hold include/linux/netdevice.h:4429 [inline]
inetdev_init+0x201/0x4e0 net/ipv4/devinet.c:286
inetdev_event+0x251/0x1610 net/ipv4/devinet.c:1600
notifier_call_chain+0x19d/0x3a0 kernel/notifier.c:85
call_netdevice_notifiers_mtu net/core/dev.c:2318 [inline]
netif_set_mtu_ext+0x5aa/0x800 net/core/dev.c:9886
netif_set_mtu+0xd7/0x1b0 net/core/dev.c:9907
dev_set_mtu+0x126/0x260 net/core/dev_api.c:248
team_port_del+0xb07/0xcb0 drivers/net/team/team_core.c:1333
team_del_slave drivers/net/team/team_core.c:1936 [inline]
team_device_event+0x207/0x5b0 drivers/net/team/team_core.c:2929
notifier_call_chain+0x19d/0x3a0 kernel/notifier.c:85
call_netdevice_notifiers_extack net/core/dev.c:2281 [inline]
call_netdevice_notifiers net/core/dev.c:2295 [inline]
__dev_change_net_namespace+0xcb7/0x2050 net/core/dev.c:12592
do_setlink+0x2ce/0x4590 net/core/rtnetlink.c:3060
rtnl_changelink net/core/rtnetlink.c:3776 [inline]
__rtnl_newlink net/core/rtnetlink.c:3935 [inline]
rtnl_newlink+0x15a9/0x1be0 net/core/rtnetlink.c:4072
rtnetlink_rcv_msg+0x7d5/0xbe0 net/core/rtnetlink.c:6958
netlink_rcv_skb+0x232/0x4b0 net/netlink/af_netlink.c:2550
netlink_unicast_kernel net/netlink/af_netlink.c:1318 [inline]
netlink_unicast+0x80f/0x9b0 net/netlink/af_netlink.c:1344
netlink_sendmsg+0x813/0xb40 net/netlink/af_netlink.c:1894
problem. Ido Schimmel found steps to reproduce
ip link add name team1 type team
ip link add name dummy1 mtu 1499 master team1 type dummy
ip netns add ns1
ip link set dev dummy1 netns ns1
ip -n ns1 link del dev dummy1
and also found that the same issue was fixed in the bond driver in
commit f51048c3e07b ("bonding: avoid NETDEV_CHANGEMTU event when
unregistering slave").
Let's do similar thing for the team driver, with commit ad7c7b2172c3 ("net:
hold netdev instance lock during sysfs operations") and commit 303a8487a657
("net: s/__dev_set_mtu/__netif_set_mtu/") also applied. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw89: pci: validate sequence number of TX release report
Hardware rarely reports abnormal sequence number in TX release report,
which will access out-of-bounds of wd_ring->pages array, causing NULL
pointer dereference.
BUG: kernel NULL pointer dereference, address: 0000000000000000
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP NOPTI
CPU: 1 PID: 1085 Comm: irq/129-rtw89_p Tainted: G S U
6.1.145-17510-g2f3369c91536 #1 (HASH:69e8 1)
Call Trace:
<IRQ>
rtw89_pci_release_tx+0x18f/0x300 [rtw89_pci (HASH:4c83 2)]
rtw89_pci_napi_poll+0xc2/0x190 [rtw89_pci (HASH:4c83 2)]
net_rx_action+0xfc/0x460 net/core/dev.c:6578 net/core/dev.c:6645 net/core/dev.c:6759
handle_softirqs+0xbe/0x290 kernel/softirq.c:601
? rtw89_pci_interrupt_threadfn+0xc5/0x350 [rtw89_pci (HASH:4c83 2)]
__local_bh_enable_ip+0xeb/0x120 kernel/softirq.c:499 kernel/softirq.c:423
</IRQ>
<TASK>
rtw89_pci_interrupt_threadfn+0xf8/0x350 [rtw89_pci (HASH:4c83 2)]
? irq_thread+0xa7/0x340 kernel/irq/manage.c:0
irq_thread+0x177/0x340 kernel/irq/manage.c:1205 kernel/irq/manage.c:1314
? thaw_kernel_threads+0xb0/0xb0 kernel/irq/manage.c:1202
? irq_forced_thread_fn+0x80/0x80 kernel/irq/manage.c:1220
kthread+0xea/0x110 kernel/kthread.c:376
? synchronize_irq+0x1a0/0x1a0 kernel/irq/manage.c:1287
? kthread_associate_blkcg+0x80/0x80 kernel/kthread.c:331
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:295
</TASK>
To prevent crash, validate rpp_info.seq before using. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: qcom: q6asm: drop DSP responses for closed data streams
'Commit a354f030dbce ("ASoC: qcom: q6asm: handle the responses
after closing")' attempted to ignore DSP responses arriving
after a stream had been closed.
However, those responses were still handled, causing lockups.
Fix this by unconditionally dropping all DSP responses associated with
closed data streams. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: Fix "scheduling while atomic" in IPsec MAC address query
Fix a "scheduling while atomic" bug in mlx5e_ipsec_init_macs() by
replacing mlx5_query_mac_address() with ether_addr_copy() to get the
local MAC address directly from netdev->dev_addr.
The issue occurs because mlx5_query_mac_address() queries the hardware
which involves mlx5_cmd_exec() that can sleep, but it is called from
the mlx5e_ipsec_handle_event workqueue which runs in atomic context.
The MAC address is already available in netdev->dev_addr, so no need
to query hardware. This avoids the sleeping call and resolves the bug.
Call trace:
BUG: scheduling while atomic: kworker/u112:2/69344/0x00000200
__schedule+0x7ab/0xa20
schedule+0x1c/0xb0
schedule_timeout+0x6e/0xf0
__wait_for_common+0x91/0x1b0
cmd_exec+0xa85/0xff0 [mlx5_core]
mlx5_cmd_exec+0x1f/0x50 [mlx5_core]
mlx5_query_nic_vport_mac_address+0x7b/0xd0 [mlx5_core]
mlx5_query_mac_address+0x19/0x30 [mlx5_core]
mlx5e_ipsec_init_macs+0xc1/0x720 [mlx5_core]
mlx5e_ipsec_build_accel_xfrm_attrs+0x422/0x670 [mlx5_core]
mlx5e_ipsec_handle_event+0x2b9/0x460 [mlx5_core]
process_one_work+0x178/0x2e0
worker_thread+0x2ea/0x430 |
| In the Linux kernel, the following vulnerability has been resolved:
netconsole: avoid OOB reads, msg is not nul-terminated
msg passed to netconsole from the console subsystem is not guaranteed
to be nul-terminated. Before recent
commit 7eab73b18630 ("netconsole: convert to NBCON console infrastructure")
the message would be placed in printk_shared_pbufs, a static global
buffer, so KASAN had harder time catching OOB accesses. Now we see:
printk: console [netcon_ext0] enabled
BUG: KASAN: slab-out-of-bounds in string+0x1f7/0x240
Read of size 1 at addr ffff88813b6d4c00 by task pr/netcon_ext0/594
CPU: 65 UID: 0 PID: 594 Comm: pr/netcon_ext0 Not tainted 6.19.0-11754-g4246fd6547c9
Call Trace:
kasan_report+0xe4/0x120
string+0x1f7/0x240
vsnprintf+0x655/0xba0
scnprintf+0xba/0x120
netconsole_write+0x3fe/0xa10
nbcon_emit_next_record+0x46e/0x860
nbcon_kthread_func+0x623/0x750
Allocated by task 1:
nbcon_alloc+0x1ea/0x450
register_console+0x26b/0xe10
init_netconsole+0xbb0/0xda0
The buggy address belongs to the object at ffff88813b6d4000
which belongs to the cache kmalloc-4k of size 4096
The buggy address is located 0 bytes to the right of
allocated 3072-byte region [ffff88813b6d4000, ffff88813b6d4c00) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Adjust PHY FSM transition to TX_EN-to-PLL_ON for TMDS on DCN35
[Why]
A backport of the change made for DCN401 that addresses an issue where
we turn off the PHY PLL when disabling TMDS output, which causes the
OTG to remain stuck.
The OTG being stuck can lead to a hang in the DCHVM's ability to ACK
invalidations when it thinks the HUBP is still on but it's not receiving
global sync.
The transition to PLL_ON needs to be atomic as there's no guarantee
that the thread isn't pre-empted or is able to complete before the
IOMMU watchdog times out.
[How]
Backport the implementation from dcn401 back to dcn35.
There's a functional difference in when the eDP output is disabled in
dcn401 code so we don't want to utilize it directly. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix signededness bug in smb_direct_prepare_negotiation()
smb_direct_prepare_negotiation() casts an unsigned __u32 value
from sp->max_recv_size and req->preferred_send_size to a signed
int before computing min_t(int, ...). A maliciously provided
preferred_send_size of 0x80000000 will return as smaller than
max_recv_size, and then be used to set the maximum allowed
alowed receive size for the next message.
By sending a second message with a large value (>1420 bytes)
the attacker can then achieve a heap buffer overflow.
This fix replaces min_t(int, ...) with min_t(u32) |
