| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: SOF: Intel: hda-sdw-bpt: Stop active DMA before closing BPT streams
When sdw_enable_stream() fails in intel_ace2x_bpt_send_async() after
hda_sdw_bpt_send_async() has already started the TX and RX DMA streams,
intel_ace2x_bpt_close_stream() invokes hda_sdw_bpt_close() directly
without calling hda_sdw_bpt_wait(). As a result,
hda_sdw_bpt_dma_deprepare() tears down the DMA buffers and BDL while
the DMA hardware is still running.
Disable any running TX or RX BPT DMA stream at the start of
hda_sdw_bpt_close() before unmapping channels and depreparing DMA
resources. |
| In the Linux kernel, the following vulnerability has been resolved:
s390/pci: Fix MSI directed-mode teardown IRQ bit count
On s390 with directed interrupts enabled, zpci_msi_teardown_directed()
frees the platform's maximum number of MSI bits (zdev->max_msi) instead
of the actual allocated count (zdev->msi_nr_irqs). This corrupts the
shared IRQ bitmap used by all PCI functions, causing lost interrupts and
heap corruption. Fix zpci_msi_teardown_directed() to only free the
actual allocated IRQ bit count. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/cma: don't release CMA pages still in use
When a driver calls dma_free_contiguous() before quiescing DMA, the
page might still have a reference from the device.
put_page_testzero() there returns false, WARN fires, but the code proceeds
to free_contig_frozen_range() putting a live page onto buddy and clearing
the bitmap. A subsequent allocation can hand the same PFN to a new
owner while the original holder still references it.
A concurrent put_page() that drops the last reference between the
testzero loop and free_contig_frozen_range() can double-queue the page
via page->lru, corrupting buddy lists.
Avoid the corruption by not freeing a CMA region if any of the
pages inside are still in use.
Make it explicit in the warning that the driver allowed a leak.
While at it, use page_ref_freeze() to make the semantics clearer and
switch to pr_warn_ratelimited().
[ david: use page_ref_freeze() + pr_warn_ratelimited() ] |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Avoid closing unowned DDC pins
[WHY]
dal_ddc_open() cleans up pins it acquires on later failures. If the
data-pin open fails, this attempt acquired nothing. If opening the
clock pin or configuring fails, dal_ddc_open() closes the pins it
opened. An extra dal_ddc_close() is unnecessary and unsafe:
GPIO_RESULT_ALREADY_OPENED can mean AUX owns the existing handles,
and closing them here would disrupt AUX.
[HOW]
Remove the extra dal_ddc_close() from the failed-open path.
(cherry picked from commit 175ae7772b68757b4932f34ff862923cab7abe21) |
| In the Linux kernel, the following vulnerability has been resolved:
mm/khugepaged: preserve dirty bits when collapsing PTE-mapped THPs
try_collapse_pte_mapped_thp() clears PTEs without transferring their dirty
bits to the folio. A shmem read fault can map a clean folio writable, so
a later store only dirties the PTE. Losing that dirty bit allows reclaim
to discard modified data.
The assumption that regular files are read-only is also obsolete since
commit 1b6444331bebb ("mm/khugepaged: enable clean pagecache folio collapse
for writable files"). In any case, transferring PTE dirty bits to the folio
when removing mappings (and while the folio is still mapped) is the right
thing to do.
Use get_and_clear_ptes() to collect the dirty bits and mark the folio
dirty before unmapping it. Update the comment.
This was reproduced with shmem using MADV_COLLAPSE followed by
MADV_PAGEOUT.
Fix generated by an LLM and sent by Chris Mason in private.
[ david: adjust comment; simplify description; cover file-thp as well ] |
| In the Linux kernel, the following vulnerability has been resolved:
xfs: mark the inode preallocated for pNFS write layouts past EOF
xfs_fs_map_blocks() marks the inode XFS_DIFLAG_PREALLOC only when it
allocates blocks for a write layout. A write layout past EOF can also
hand out allocated blocks, such as speculative preallocation. blockgc
then frees them under the layout, and another file may get them.
Mark the inode whenever a write mapping ends past EOF. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/madvise: fix data loss from MADV_FREE on a KSM page
MADV_FREE can clear the dirty flag of a singly mapped KSM folio. The
folio remains in the stable tree and can gain new mappings without being
dirtied again. Once marked lazyfree, reclaim can discard data that those
mappings still need.
KSM always marks a folio dirty when converting it to a KSM folio in
try_to_merge_one_page(). Marking a folio lazyfree clears PG_swapbacked
but leaves PG_dirty unchanged. Preserving PG_dirty makes reclaim restore
PG_swapbacked instead of discarding the folio. This also protects folios
that were already lazyfree when KSM converted them.
Skip KSM folios before clearing their dirty flag, checking under the
folio lock to serialize with KSM conversion. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: conntrack: tcp: use UNACK timeout for non-closing RST packets
Commit be0502a3f2e9 ("netfilter: conntrack: tcp: only close if RST
matches exact sequence") keeps an established conntrack entry in
ESTABLISHED when an in-window RST does not match the expected sequence
number exactly, so the endpoint can validate the RST with a challenge
ACK.
The timeout selection nevertheless uses the CLOSE timeout for every RST
packet. The bug is that timeout selection is based on the packet type,
not on the state transition result: even when RST validation keeps
new_state in ESTABLISHED, the timeout is still forced to
TCP_CONNTRACK_CLOSE.
Linux TCP independently rate limits challenge ACKs per socket. A second
non-exact RST can therefore arrive after the first challenge ACK has
restored the timeout but before the rate limit expires. The second RST
lowers the timeout to 10 seconds again while the endpoint suppresses the
second challenge ACK, allowing the conntrack entry to expire while both
TCP endpoints remain established.
Using the ESTABLISHED timeout for such RSTs would avoid this short
expiration window, but it could also retain stale entries for the
five-day default because conntrack cannot reliably match the endpoint's
exact TCP state.
Use the UNACK timeout for RST packets that leave the conntrack entry in
TCP_CONNTRACK_ESTABLISHED. Exact-match RSTs and accepted RST packet
trains still fall through to timeouts[new_state], which preserves the
CLOSE timeout when conntrack accepts the RST as closing the flow.
This avoids the aggressive 10-second expiration window for non-exact
RSTs while preserving the short timeout for RSTs that conntrack accepts
as closing the flow. |
| In the Linux kernel, the following vulnerability has been resolved:
fs: don't silently unmount busy mounts
The propagate_mount_busy() helper exists to decide whether a synchronous
can suceed. It does that by looking at the copies of the victims in the
mounts its parent propagates to. One of those functions from propagation
hell.
It skips a copy that has child mounts except for the case of a single
child mount covering the copy's root. That algorithm used to be exact.
It isn't anymore.
Originally only childless copies were unmounted during propagation.
And 1064f874abc0 ("mnt: Tuck mounts under others instead of creating
shadow/side mounts.") ended up adding covered mounts to both sides in
one go.
Along came 99b19d16471e ("mnt: In propgate_umount handle visiting mounts
in any order") and that started to unmount more than before:
[1]: A copy of a mount is unmounted when each of its children is either
its overmount or a copy of the victim itself. In the former case
the overmount gets reparented. In the latter case the copy of the
victim will end up being unmounted.
So propagate_umount() ended up being rewritten without adjusting
propagate_mount_busy(). And currently propagate_mount_busy() doesn't
look at copies of the victim that have two or more children nor a single
child that is not the overmount.
So any such copy in [1] is not checked for
references. The result is that a synchronous unmount succeeds, pulling
out a mount that is still in use.
A container can run into this with its own mounts. The host shares a
tree with the container and the host has a mount in that tree:
mount -t tmpfs none /mnt
mount --make-shared /mnt
mount -t tmpfs none /mnt/a
The container's /mnt is a slave copy of the host mount. The container
now takes a detached copy of the tree and mounts that copy beneath its
propagated copy of /mnt/a and keeps the file descriptor to the tree
open:
unshare -m --propagation unchanged
mount --make-rslave /
fd = open_tree(AT_FDCWD, "/mnt", OPEN_TREE_CLONE | AT_RECURSIVE)
move_mount(fd, "", AT_FDCWD, "/mnt/a", MOVE_MOUNT_BENEATH)
grep /mnt /proc/self/mountinfo
775 355 ... /mnt ... master:646
777 775 ... /mnt/a ... master:646
776 777 ... /mnt/a ... master:647
778 777 ... /mnt/a/a ... master:647
The now attached tree (777) is now mounted beneath the container's copy
of /mnt/a. That's also where the host mount sits (as seen from the host
mount namespace). So the propagated copy (776) of the host's mount is on
top of its root and the copy of that (778) is inside it. Now the host
runs:
umount /mnt/a
and it succeeds. The moved tree tree and the copy inside of it are gone
from the container. Now only the propagated copy is left and it got
reparented to where it was before:
grep /mnt /proc/self/mountinfo
775 355 ... /mnt ... master:646
776 775 ... /mnt/a ...
But the file descriptor still refers to the moved tree. So a synchronous
umount detached a mount that is still in use.
Teach propagate_mount_busy() the same checks that propagate_umount()
does. It now checks for a single victim mount without children
for which it can assume that MNT_LOCKED is cleared on every copy like
propagate_umount() does. The copies form chains. IOW, when a copy itself
receives propagation from the victim's parent then the mount at the same
mountpoint inside that copy is a copy as well. Whether a mount receives
propagation from the victim's can simply be checked by walking its
masters. Walk each chain once from its top so we are sure that nested
copies stay linear. Check every reference once of every copy that gets
unmounted. |
| In the Linux kernel, the following vulnerability has been resolved:
i2c: i801: fix hardware state machine corruption in error path
A severe livelock and subsequent Hung Task panic were observed in the
i2c-i801 driver during concurrent Fuzzing. The crash is caused by an
unconditional hardware register cleanup in the error handling path of
i801_access().
When i801_check_pre() fails (e.g., returning -EBUSY because the SMBus
controller is actively used by BIOS/ACPI), the kernel does not actually
acquire the hardware ownership. However, the code jumps to the 'out'
label and executes:
iowrite8(SMBHSTSTS_INUSE_STS | STATUS_FLAGS, SMBHSTSTS(priv));
This forcefully clears the INUSE_STS lock and resets the hardware status
flags without owning the controller. Doing so interrupts ongoing BIOS/ACPI
transactions and totally corrupts the SMBus hardware state machine.
Consequently, all subsequent i801_access() calls fail at the pre-check
stage, triggering an endless stream of "SMBus is busy, can't use it!"
error logs. Over a slow serial console, this printk flood monopolizes
the CPU (Console Livelock), starving other processes trying to acquire
the mmap_lock down_read semaphore, ultimately triggering the hung task
watchdog.
Fix this by moving the 'out' label below the hardware register cleanup.
If i801_check_pre() fails, we safely bypass the iowrite8() and only
release the software locks (pm_runtime and mutex), strictly adhering to
the rule of not releasing resources that were never acquired. |
| In the Linux kernel, the following vulnerability has been resolved:
hsr: Remove WARN_ONCE() in hsr_addr_is_self().
syzbot reported the warning [0] in hsr_addr_is_self(),
whose assumption is simply wrong.
hsr->self_node is cleared in hsr_del_self_node(), which
is called from hsr_dellink().
Since dev->rtnl_link_ops->dellink() is called before
unregister_netdevice_many(), there is a window when
user can find the device but without hsr->self_node.
Let's remove WARN_ONCE() in hsr_addr_is_self().
[0]:
HSR: No self node
WARNING: net/hsr/hsr_framereg.c:39 at hsr_addr_is_self+0x211/0x3f0 net/hsr/hsr_framereg.c:39, CPU#0: syz.4.16848/17220
Modules linked in:
CPU: 0 UID: 0 PID: 17220 Comm: syz.4.16848 Tainted: G L syzkaller #0 PREEMPT_{RT,(full)}
Tainted: [L]=SOFTLOCKUP
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/18/2026
RIP: 0010:hsr_addr_is_self+0x211/0x3f0 net/hsr/hsr_framereg.c:39
Code: 33 2f 41 0f b7 dd 89 ee 09 de 31 ff e8 c8 b4 c6 f6 09 dd 74 54 e8 0f b0 c6 f6 31 ed eb 53 e8 06 b0 c6 f6 48 8d 3d 2f 50 9c 04 <67> 48 0f b9 3a 31 ed eb 42 e8 c1 13 1f 00 89 c5 31 ff 89 c6 e8 96
RSP: 0018:ffffc900041c70e0 EFLAGS: 00010283
RAX: ffffffff8afdc6ca RBX: ffffffff8afdc4e6 RCX: 0000000000080000
RDX: ffffc90010493000 RSI: 0000000000000948 RDI: ffffffff8f9a1700
RBP: 0000000000000001 R08: 0000000000000000 R09: 0000000000000000
R10: ffffc900041c71e8 R11: fffff52000838e3f R12: dffffc0000000000
R13: ffff888041f9e3c0 R14: ffff888086ee3802 R15: 0000000000000000
FS: 00007f6fe985d6c0(0000) GS:ffff888126176000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f80bd437dac CR3: 0000000025096000 CR4: 00000000003526f0
DR0: ffffffffffffffff DR1: 00000000000001f8 DR2: 0000000000000002
DR3: ffffffffefffff15 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
check_local_dest net/hsr/hsr_forward.c:592 [inline]
fill_frame_info net/hsr/hsr_forward.c:728 [inline]
hsr_forward_skb+0xa11/0x2a80 net/hsr/hsr_forward.c:739
hsr_dev_xmit+0x253/0x370 net/hsr/hsr_device.c:236
__netdev_start_xmit include/linux/netdevice.h:5368 [inline]
netdev_start_xmit include/linux/netdevice.h:5377 [inline]
xmit_one net/core/dev.c:3888 [inline]
dev_hard_start_xmit+0x2df/0x860 net/core/dev.c:3904
__dev_queue_xmit+0x1428/0x3900 net/core/dev.c:4870
neigh_output include/net/neighbour.h:556 [inline]
ip_finish_output2+0xcec/0x10b0 net/ipv4/ip_output.c:237
ip_send_skb net/ipv4/ip_output.c:1510 [inline]
ip_push_pending_frames+0x8b/0x110 net/ipv4/ip_output.c:1530
raw_sendmsg+0x1547/0x1a50 net/ipv4/raw.c:659
sock_sendmsg_nosec net/socket.c:787 [inline]
__sock_sendmsg net/socket.c:802 [inline]
____sys_sendmsg+0x7da/0x9c0 net/socket.c:2698
___sys_sendmsg+0x2a5/0x360 net/socket.c:2752
__sys_sendmsg net/socket.c:2784 [inline]
__do_sys_sendmsg net/socket.c:2789 [inline]
__se_sys_sendmsg net/socket.c:2787 [inline]
__x64_sys_sendmsg+0x1c3/0x2a0 net/socket.c:2787
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0x15f/0xf80 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7f6feb62ce59
Code: ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 e8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007f6fe985d028 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007f6feb8a6090 RCX: 00007f6feb62ce59
RDX: 0000000000000000 RSI: 0000200000000000 RDI: 0000000000000004
RBP: 00007f6feb6c2d6f R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 00007f6feb8a6128 R14: 00007f6feb8a6090 R15: 00007ffcf01cc488
</TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
dm cache: fix write hang in passthrough mode
The invalidate_remove() function has incomplete logic for handling write
hit bios after cache invalidation. It sets up the remapping for the
overwrite_bio but then drops it immediately without submission, causing
write operations to hang.
Fix by adding a new invalidate_committed() continuation that submits
the remapped writes to the cache origin after metadata commit completes,
while using the overwrite_endio hook to ensure proper completion
sequencing. This maintains existing coherency. Also improve error
handling in invalidate_complete() to preserve the original error status
instead of using bio_io_error() unconditionally. |
| In the Linux kernel, the following vulnerability has been resolved:
powerpc, perf: Check that current->mm is alive before getting user callchain
It may happen that mm is already released, which leads to kernel panic.
This adds the NULL check for current->mm, similarly to
commit 20afc60f892d ("x86, perf: Check that current->mm is alive before getting user callchain").
I was getting this panic when running a profiling BPF program
(profile.py from bcc-tools):
[26215.051935] Kernel attempted to read user page (588) - exploit attempt? (uid: 0)
[26215.051950] BUG: Kernel NULL pointer dereference on read at 0x00000588
[26215.051952] Faulting instruction address: 0xc00000000020fac0
[26215.051957] Oops: Kernel access of bad area, sig: 11 [#1]
[...]
[26215.052049] Call Trace:
[26215.052050] [c000000061da6d30] [c00000000020fc10] perf_callchain_user_64+0x2d0/0x490 (unreliable)
[26215.052054] [c000000061da6dc0] [c00000000020f92c] perf_callchain_user+0x1c/0x30
[26215.052057] [c000000061da6de0] [c0000000005ab2a0] get_perf_callchain+0x100/0x360
[26215.052063] [c000000061da6e70] [c000000000573bc8] bpf_get_stackid+0x88/0xf0
[26215.052067] [c000000061da6ea0] [c008000000042258] bpf_prog_16d4ab9ab662f669_do_perf_event+0xf8/0x274
[...]
In addition, move storing the top-level stack entry to generic
perf_callchain_user to make sure the top-evel entry is always captured,
even if current->mm is NULL.
[Maddy: fixed message to avoid checkpatch format style error] |
| In the Linux kernel, the following vulnerability has been resolved:
USB: wdm: close race between wdm_open and wdm_wwan_port_stop
Clearing WDM_WWAN_IN_USE must be the last action or
we can open a chardev whose URBs are still poisoned |
| In the Linux kernel, the following vulnerability has been resolved:
namespace: check a submount for references right before unmounting it
shrink_submounts() and mark_mounts_for_expiry() first collect all the
mounts they are allowed to unmount and then unmount them.
Whether a mount is busy is decided by propagate_mount_busy() on the
tree. But unmounting the first mount changes the tree that the second
one propagates into. propagate_umount()
moves a surviving overmount off a copy it unmounts and mounts it where
the copy was mounted. If that's where the propagated copy of the second
victim is looked up the overmount becomes a candidate of the second
umount_tree(). It's childless and so trim_one() commits it without
looking at its reference count.
So a synchronous umount pulls out a busy mount that is in use somewhere
else and marks it MNT_SYNC_UMOUNT while it has users:
umount2(/tmp/plshrink/p1, 0) = 0 errno 0
cwd is (unreachable)
The same two umounts requested one after the other fail with EBUSY.
This needs a mount with MNT_SHRINKABLE, i.e., automounted submounts of
NFS, AFS and CIFS or the tracefs mount below debugfs. Bind mounts
inherit the flag.
Check each mount right before it is unmounted under the same hold of
namespace_sem and mount_lock as the umount itself. Make sure that the
algorithm stays linear. |
| In the Linux kernel, the following vulnerability has been resolved:
gpio: exar: initialize the ID before registering its cleanup
devm_add_action_or_reset() invokes the cleanup action immediately when
registering the action fails. gpio_exar_probe() currently stores the
allocated ID in exar_gpio only after registering the action, so that
failure makes exar_devm_ida_free() release ID 0. If the allocated ID is
nonzero, this leaks that ID and can free ID 0 belonging to another device.
Store the ID before registering the cleanup action so both the immediate
failure path and normal device teardown release the correct allocation. |
| In the Linux kernel, the following vulnerability has been resolved:
binder: fix is_failure flag for superseded transaction cleanup
When a TF_UPDATE_TXN transaction supersedes a pending async transaction,
binder_release_entire_buffer() is called with is_failure=false. Since the
superseded transaction was never delivered, binder_apply_fd_fixups() was
never called and no fds were installed in the target process.
With is_failure=false, the BINDER_TYPE_FDA cleanup handler interprets
stale buffer contents as installed fd numbers and passes them to
binder_deferred_fd_close(), closing unrelated file descriptors.
Pass is_failure=true since the transaction was never delivered to the
target, matching the semantics of all other undelivered-transaction
cleanup paths. |
| In the Linux kernel, the following vulnerability has been resolved:
tracing/user_events: Don't destroy fields when event removal fails
destroy_user_event() destroys the event's fields before attempting to
remove the trace event call. If user_event_set_call_visible() fails,
e.g. because the event is still enabled and trace_remove_event_call()
returns -EBUSY, the event is left registered with an irreversibly
destroyed field list. Any subsequent interaction with the event then
operates on an empty field list while it is still fully visible in
tracefs.
Move the field destruction after the call removal, and splice the
field list back onto the event when the removal fails so the event
remains in a consistent state. |
| In the Linux kernel, the following vulnerability has been resolved:
spi: fsl: fix controller deregistration
Make sure to deregister the controller before releasing underlying
resources like DMA during driver unbind. |
| In the Linux kernel, the following vulnerability has been resolved:
spi: rspi: fix controller deregistration
Make sure to deregister the controller before releasing underlying
resources like DMA during driver unbind. |