| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
bonding: refuse to enslave CAN devices
syzbot reported a kernel paging request crash in
can_rx_unregister() inside net/can/af_can.c. The crash occurs
because a virtual CAN device (vxcan) is being enslaved to a
bonding master.
During the enslavement process, the bonding driver mutates
and modifies the network device states to fit an Ethernet-like
aggregation model. However, CAN devices operate on a completely
different Layer 2 architecture, relying on the CAN mid-layer
private data structure (can_ml_priv) instead of standard
Ethernet structures. Since bonding does not initialize or
maintain these CAN structures, subsequent operations on the
half-enslaved interface (such as closing associated sockets
via isotp_release) lead to a null-pointer dereference when
accessing the CAN receiver lists.
Bonding CAN interfaces is architecturally invalid as CAN lacks
MAC addresses, ARP capabilities, and standard Ethernet
link-layer mechanisms. While generic loopback devices are
blocked globally in net/core/dev.c, virtual CAN devices
bypass this check because they do not carry the IFF_LOOPBACK
flag, despite acting as local software-loopbacks.
Fix this by explicitly blocking network devices of type
ARPHRD_CAN from being enslaved at the very beginning of
bond_enslave(). This prevents illegal state mutations,
eliminates the resulting KASAN crashes, and avoids potential
memory leaks from incomplete socket cleanups.
As the CAN support has been added a long time after bonding
the Fixes-tag points to the introduction of ARPHRD_CAN that
would have needed a specific handling in bonding_main.c. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: 6lowpan: check skb_clone() return value in send_mcast_pkt()
The skb_clone() function can return NULL if memory allocation fails.
send_mcast_pkt() calls skb_clone() without checking the return value, which
can lead to a NULL pointer dereference in send_pkt() when it dereferences
skb->data.
Add a NULL check after skb_clone() and skip the peer if the clone fails. |
| In the Linux kernel, the following vulnerability has been resolved:
tunnels: do not assume transport header in iptunnel_pmtud_check_icmp()
In some cases, iptunnel_pmtud_check_icmp() can be called while
skb transport header is not set.
This triggers an out-of-bound access, because
(typeof(skb->transport_header))~0U is 65535.
Access the icmp header based on IPv4 network header,
after making sure icmp->type is present in skb linear part.
Note that iptunnel_pmtud_check_icmpv6()) is fine. |
| In the Linux kernel, the following vulnerability has been resolved:
tunnels: load network headers after skb_cow() in iptunnel_pmtud_build_icmp[v6]()
Sashiko found that iptunnel_pmtud_build_icmp() and
iptunnel_pmtud_build_icmpv6() were caching ip_hdr() and ipv6_hdr()
before an skb_cow() call which can reallocate skb->head.
Fix this possible UAF by initializing the local variables
after the skb_cow() call.
Remove skb_reset_network_header() calls which were not needed. |
| In the Linux kernel, the following vulnerability has been resolved:
ethtool: cmis: validate start_cmd_payload_size from module
The CMIS firmware update code reads start_cmd_payload_size from
the module's FW Management Features CDB reply and uses it directly
as the byte count for memcpy. The destination buffer is 112 bytes
(ETHTOOL_CMIS_CDB_LPL_MAX_PL_LENGTH - 8). So a malicious
module (or corrupted response) can cause a OOB write later on in
cmis_fw_update_start_download().
Let's error out. If modules that expect longer LPL writes actually
exist we should revisit.
struct cmis_cdb_start_fw_download_pl's definition has to move,
no change there. |
| A flaw was found in the Linux kernels implementation of audit rules, where a syscall can unexpectedly not be correctly not be logged by the audit subsystem |
| A memory disclosure flaw was found in the Linux kernel's ethernet drivers, in the way it read data from the EEPROM of the device. This flaw allows a local user to read uninitialized values from the kernel memory. The highest threat from this vulnerability is to confidentiality. |
| Commvault Web Server has an unspecified vulnerability that can be exploited by a remote, authenticated attacker. According to the Commvault advisory: "Webservers can be compromised through bad actors creating and executing webshells." Fixed in version 11.36.46, 11.32.89, 11.28.141, and 11.20.217 for Windows and Linux platforms. This vulnerability was added to the CISA Known Exploited Vulnerabilities (KEV) Catalog on 2025-04-28. |
| In the Linux kernel, the following vulnerability has been resolved:
tcp: fix use-after-free of retransmit_skb_hint in tcp_send_synack()
When tcp_send_synack() replaces the cloned SYN skb at the head of the
retransmit queue with a copy, it frees the original with
tcp_rtx_queue_unlink_and_free() and only repairs tp->highest_sack.
tp->retransmit_skb_hint keeps pointing at the freed
skbuff_fclone_cache object.
The dangling hint is read in tcp_verify_retransmit_hint() and used as
the root of the rbtree walk in tcp_xmit_retransmit_queue(). An
unprivileged TFO client (sendmsg(MSG_FASTOPEN)) can arm the hint with
an attacker-supplied ICMP fragmentation-needed message, after which a
simultaneous open frees the armed SYN skb:
BUG: KASAN: slab-use-after-free in tcp_mark_skb_lost (net/ipv4/tcp_input.c:1316)
Read of size 4 at addr ffff88800604d928 by task swapper/1/0
Call Trace:
tcp_mark_skb_lost (net/ipv4/tcp_input.c:1316)
tcp_simple_retransmit (net/ipv4/tcp_input.c:3158)
tcp_v4_err (net/ipv4/tcp_ipv4.c:587)
Sync the hint to the copy. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/hugetlb: preserve mremap address delta when skipping page tables
move_hugetlb_page_tables() optimizes mremap() by advancing to the last
entry in the page table when the source page table does not exist, either
initially or after unsharing a PMD table. The common loop increment then
steps to the first entry in the next page table.
However, the code advances both the source and destination addresses to
the last entries in their respective page tables, which is wrong. The
destination address must be advanced only by the same amount as the source
address.
If the source and destination offsets within their page tables differ, the
destination address can be advanced too far, causing follow-up issues.
Fix this by advancing the destination address by the source advance
distance.
With a reproducer, we were able to trigger a kernel panic on x86-64. With
this fix in place, we can no longer reproduce the issue. |
| Origin validation error in .NET allows an unauthorized attacker to disclose information over a network. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/rxe: Restore HMM_PFN_WRITE check in ODP write paths
Commit 0b261d7c1cd3 ("RDMA/rxe: Break endless pagefault loop for RO
pages") dropped the access permission test from rxe_check_pagefault()
and left only HMM_PFN_VALID. A page faulted in read-only, for example
a page-cache folio behind a PROT_READ file mapping, then satisfies the
check and ODP write operations (RDMA WRITE, RDMA READ response, SEND
payload, atomics) modify it through kmap without ever breaking CoW.
An unprivileged user can register an ODP MR over such a mapping and
have incoming RDMA traffic overwrite the page cache of a file it only
holds O_RDONLY, including /etc/passwd or setuid binaries. This is the
same primitive class as Dirty COW and CVE-2022-2590.
mlx5 has the missing invariant: its ODP path sets the device write bit
only for pfns that carry HMM_PFN_WRITE. Restore it in rxe by requiring
HMM_PFN_WRITE in rxe_check_pagefault() for every operation except
RXE_PAGEFAULT_RDONLY. A write to a non-writable VMA now fails the one
fault attempt with -EPERM from hmm_vma_fault() instead of re-faulting
forever. For a writable VMA the fault breaks CoW and the write lands
in the private page.
Keep pmem flushes on the read-only check. arch_wb_cache_pmem() never
modifies memory, and the FLUSH access bits do not make the umem
writable, so classifying flushes as writes would make every flush
against a flush-only MR fail. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: fix smbd_connection leak on cifs_get_tcp_session() error
When an RDMA connection is successfully established via
smbd_get_connection() but cifs_get_tcp_session() later fails (e.g.
kthread_create() returns an error), the error path frees tcp_ses
without first destroying the smbd_connection.
Fix this by calling smbd_destroy() in the out_err cleanup path before
kfree(tcp_ses). smbd_destroy() safely handles the case where
smbd_conn is NULL, so it can be called unconditionally. |
| In the Linux kernel, the following vulnerability has been resolved:
IB/iser: reject a remote invalidation of an unregistered direction
A write command whose data is sent entirely as immediate data is not
registered. iser_reg_mem_fastreg() takes the DMA key path and leaves
rdma_reg[ISER_DIR_OUT].desc at NULL, while iser_dma_map_task_data() has
already set dir[ISER_DIR_OUT].
iser_check_remote_inv() looks at dir[] alone and hands the descriptor to
iser_inv_desc(), which reads desc->sig_protected. A target that answers
such a command with IB_WR_SEND_WITH_INV faults the initiator.
Leaving those commands unregistered is deliberate.
The same function already terminates the connection when a target sends
a remote invalidation the initiator did not ask for. A target that
invalidates a direction that was never registered is in the same class,
so give it the same answer.
Oops: general protection fault, probably for non-canonical address 0xdffffc0000000004: 0000 [#1] SMP KASAN NOPTI
KASAN: null-ptr-deref in range [0x0000000000000020-0x0000000000000027]
CPU: 0 UID: 0 PID: 40 Comm: kworker/u8:2 Not tainted 7.2.0-rc5-ISERHOST-gf5098b6bae76-dirty #3 PREEMPT(lazy)
Hardware name: QEMU Ubuntu 24.04 PC v2 (i440FX + PIIX, arch_caps fix, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
Workqueue: rxe_wq do_work
RIP: 0010:iser_task_rsp+0x6d6/0xec0
Code: 48 c1 ea 03 80 3c 02 00 0f 85 ba 06 00 00 48 8b 9b 78 01 00 00 48 b8 00 00 00 00 00 fc ff df 48 8d 7b 20 48 89 fa 48 c1 ea 03 <0f> b6 04 02 84 c0 74 06 0f 8e 76 06 00 00 80 7b 20 00 0f 84 3d 04
RSP: 0018:ffff88811b008db8 EFLAGS: 00010202
RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 0000000000001848
RDX: 0000000000000004 RSI: 1ffff11021587b12 RDI: 0000000000000020
RBP: ffff88810adc1ae4 R08: ffff888109b7f860 R09: ffffffff90a922c0
R10: ffff88810adc1a1c R11: 000000000000003c R12: ffff888109b7f800
R13: ffff88810adc1acc R14: ffff888109b7f820 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff88818a676000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000005afe2b CR3: 000000010af23005 CR4: 0000000000770ef0
PKRU: 55555554
Call Trace:
<IRQ>
__ib_process_cq+0xe1/0x390
ib_poll_handler+0x6e/0x200
irq_poll_softirq+0x1df/0x480
? clockevents_program_event+0x2ba/0x860
? __pfx_irq_poll_softirq+0x10/0x10
handle_softirqs+0x18e/0x590
? __pfx_handle_softirqs+0x10/0x10
? __hrtimer_rearm_deferred+0x156/0x450
do_softirq+0x3b/0x60
</IRQ>
<TASK>
__local_bh_enable_ip+0x61/0x70
__alloc_skb+0x732/0x890
? _raw_spin_lock_irqsave+0x85/0xe0
? __pfx___alloc_skb+0x10/0x10
? _raw_read_unlock_irqrestore+0x16/0x50
rxe_init_packet+0x16b/0x4f0
prepare_ack_packet+0xb8/0x830
rxe_receiver+0x499/0x9980
? __pfx_rxe_receiver+0x10/0x10
? rxe_completer+0x29e5/0x38c0
? hrtimer_start_range_ns_common+0x75f/0x1730
? hrtimer_start_range_ns+0xa6/0x2c0
? __pfx__raw_spin_lock_irqsave+0x10/0x10
? __pfx_rxe_receiver+0x10/0x10
do_work+0x144/0x470
process_one_work+0x633/0x1030
? assign_work+0x11d/0x370
worker_thread+0x45b/0xd10
? __pfx_worker_thread+0x10/0x10
kthread+0x2c6/0x3b0
? recalc_sigpending+0x15c/0x1e0
? __pfx_kthread+0x10/0x10
ret_from_fork+0x36e/0x5a0
? __pfx_ret_from_fork+0x10/0x10
? __switch_to+0x572/0xdd0
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1a/0x30
</TASK>
Modules linked in:
---[ end trace 0000000000000000 ]--- |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/rxe: insert mcg into mcg_tree only after rxe_mcast_add() succeeds
rxe_get_mcg() publishes a newly allocated multicast group in
rxe->mcg_tree before programming the backing Ethernet multicast address
with rxe_mcast_add(), which runs outside mcg_lock. A local userspace
RDMA client reaches this path with ATTACH_MCAST on a UD QP; if
rxe_mcast_add() then returns an error (for example -ENODEV when the
backing netdev has been removed, or a propagated dev_mc_add() error),
the unwind frees the published group without removing it from the tree.
A later lookup of the same MGID dereferences the freed struct rxe_mcg
from __rxe_lookup_mcg().
Fix this by keeping the new mcg private until rxe_mcast_add() succeeds.
Split the tree publication into __rxe_publish_mcg(), call rxe_mcast_add()
before taking the tree reference, and free the still-private mcg on
failure. Because the group is never visible in mcg_tree until the
multicast address is programmed, no concurrent caller can look it up or
attach a QP to a group that is about to be torn down, so the error path
needs no conditional unwind. If another caller publishes the same MGID
while the address is being programmed, the post-add re-check under
mcg_lock finds the winner; this caller then drops its private object and
balances its own rxe_mcast_add() with rxe_mcast_del() before returning
the winner.
Reproduced by forcing the rxe_mcast_add() error return under KASAN:
without the change the next attach to the same MGID reports a
slab-use-after-free in __rxe_lookup_mcg(); with it the forced failure
returns cleanly. A no-injection attach/detach regression, including a
two-QP shared join/leave and re-attach, stays KASAN- and leak-clean. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/erdma: Use IRQ-safe XArray helpers for QP and CQ tables
Locked QP and CQ lookups from EQ interrupts can deadlock with
create-path XArray updates. If an interrupt arrives while the create
path holds the plain xa_lock, the lookup spins forever trying to
acquire the same lock.
Use IRQ-safe XArray helpers for all QP and CQ create-path updates,
including the GSI QP store and error paths. Initialize both arrays with
XA_FLAGS_LOCK_IRQ so sleeping allocations preserve interrupt state. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/mad: Fix receive buffer leak when PKey enforcement fails
ib_mad_complete_recv() initializes mad_recv_wc->rmpp_list and then runs
ib_mad_enforce_security() before linking recv_buf onto that list. On
failure it calls ib_free_recv_mad(), which only walks rmpp_list and frees
the ib_mad_private of every buffer found there. As the list is still
empty at that point, nothing is freed at all.
The caller cannot clean up either: ib_mad_recv_done() sets recv to NULL
right after ib_mad_complete_recv() returns, assuming the MAD layer took
ownership of the buffer. Every MAD that fails the PKey check therefore
leaks one ib_mad_private (about 300 bytes per IB port MAD, ~2K for OPA),
and a remote node can trigger this repeatedly by sending MADs with a
wrong PKey.
Link recv_buf onto rmpp_list right after the list is initialized, so the
error path has something to free. |
| All versions of Zammad including the latest alpha enable the local zammad user to escalate privileges to root. |
| Zammad versions 6.3.0 to 6.5.4 are vulnerable a session hijack vulnerability that leads to remote code execution as the zammad user. The bug is also present in version 7.0.0 to version 7.1.2, but not exploitable due to changes in the underlying framework. |
| In the Linux kernel, the following vulnerability has been resolved:
swiotlb: use the adjusted address for the highmem page lookup
swiotlb_bounce() reads the page frame number from the slot's recorded
orig_addr, then advances orig_addr by tlb_offset to reach the address
the caller asked about. The highmem branch mixes the two: the offset
within the page comes from the adjusted address, the page from the value
before it.
Once the adjustment crosses a page boundary the pair no longer describes
one location, and the whole copy lands one page below the intended one
for a positive tlb_offset, one above for a negative one. DMA_FROM_DEVICE
writes the device data over the wrong page and leaves the intended one
stale, DMA_TO_DEVICE feeds the device from a page the mapping may not
cover. Partial syncs through dma_sync_single_range_for_*() are what make
tlb_offset non-zero.
The branch test is picked the same way, so a slot recorded in lowmem can
be adjusted into highmem and the lowmem path then hands a highmem
address to phys_to_virt().
Take both from orig_addr once it is final and keep pfn in the branch
that uses it. PhysHighMem() asks the question straight from the address,
as dma-debug already does. |
